Le Chatelier Shift Predictor
Enter a gas reaction at equilibrium, apply a disturbance, and see the direction of the shift and the new equilibrium amounts.
↔️ What is the Le Chatelier Shift Predictor?
Le Chatelier's principle says that when a chemical system at equilibrium is disturbed, it adjusts to partly cancel the disturbance. Add a reactant and the system consumes some of it. Squeeze the container and the mixture favors the side with fewer gas molecules. Heat an exothermic reaction and the equilibrium moves toward the reactants, which absorbs part of the extra heat. The principle was stated by Henry Louis Le Chatelier in 1884, and it is the everyday shortcut for judging how an equilibrium responds to a change in conditions.
The principle matters well beyond the classroom. The Haber process for ammonia runs at high pressure because the reaction N2 + 3 H2 = 2 NH3 reduces the number of gas moles, and it removes ammonia as it forms to keep the reaction moving forward. Sulfuric acid plants, methanol synthesis and the water-gas shift reaction all rely on the same reasoning to choose pressure, temperature and feed ratios. In biochemistry and environmental chemistry the same logic explains how blood buffers respond to carbon dioxide and why dissolved gases escape when a drink is opened.
Qualitative rules can mislead when several effects compete, so this tool backs them with numbers. It treats the system as a gas reaction aA + bB = cC + dD, derives K from your equilibrium concentrations, computes the reaction quotient Q immediately after the disturbance and compares the two. If Q is below K the reaction runs forward, if it is above K it runs backward. It then solves for the extent of reaction that restores Q = K and tabulates the new concentrations. Concentration and volume changes alter Q only. A temperature change alters K itself, using the van't Hoff equation with a constant enthalpy.
It does not model catalysts, which never shift an equilibrium, or non-ideal gases, and it assumes the volume changes at constant temperature. It also differs from a plain reaction quotient calculator, which only reports Q, and from an equilibrium constant calculator, which only reports K. All concentrations and the enthalpy in the examples are illustrative values chosen to show each effect, not measured data.
📐 Formula
📖 How to Use This Calculator
Steps
💡 Example Calculations
Example 1 - Adding nitrogen to an ammonia equilibrium
N2 + 3 H2 = 2 NH3 at 0.50, 1.50 and 0.80 mol/L (illustrative), add 0.50 mol/L N2
Example 2 - Halving the volume of the same mixture
Same mixture, V2/V1 = 0.5 (compression to double pressure)
Example 3 - Heating an exothermic ammonia mixture
dH = -92.2 kJ/mol, T1 = 500 K, T2 = 600 K (illustrative), same concentrations
Example 4 - Squeezing a reaction with equal gas moles
CO + H2O = CO2 + H2 at 0.40, 0.40, 0.60, 0.60 mol/L (illustrative), V2/V1 = 0.5
Example 5 - Removing a product to pull the reaction forward
Same water-gas shift mixture, remove 0.30 mol/L of CO2 (illustrative)
❓ Frequently Asked Questions
📚 Sources and Notes
The principle and the Q versus K rule follow the Wikipedia article on Le Chatelier's principle, The Reaction Quotient and the LibreTexts chapter on shifting equilibria. The concentrations and the enthalpy in the examples are illustrative values, not measurements of a real reactor.
See also the reaction quotient calculator, the Kp and Kc calculator and the van't Hoff equation calculator.
🔗 Related Calculators
What is Le Chatelier's principle?
When a system at equilibrium is disturbed by a change in concentration, pressure, volume or temperature, it shifts in the direction that partly offsets the change. It is a qualitative rule, and comparing the reaction quotient Q with K gives the same answer quantitatively.
How do you predict the direction of the shift from Q and K?
Compute Q from the concentrations right after the disturbance and compare it with K. If Q is less than K the reaction runs forward, to the right. If Q is greater than K it runs backward, to the left. If Q equals K nothing shifts.
What happens when you add a reactant?
Q falls below K because the denominator grows, so the reaction shifts right and uses up part of the added reactant. For N2 + 3 H2 = 2 NH3 with 0.50 mol/L of N2 added to a mixture at 0.50, 1.50 and 0.80 mol/L, Q drops to half of K and the system forms more NH3.
How does pressure or volume affect equilibrium?
Halving the volume doubles every concentration. Q is multiplied by (V2/V1) raised to minus the change in gas moles. The shift goes toward the side with fewer gas moles when pressure rises, and does nothing if both sides have equal moles.
How does temperature affect equilibrium?
Temperature is the only change that alters K itself. Raising it increases K for an endothermic reaction (positive dH) and lowers K for an exothermic one. The shift follows K, as described by the van't Hoff equation, so heating favors the endothermic direction.
Does a catalyst shift the equilibrium?
No. A catalyst lowers the activation energy of both the forward and reverse reactions equally, so equilibrium is reached faster but at the same composition. K and Q are unchanged.
Does adding an inert gas shift an equilibrium?
At constant volume, no. The partial pressures and concentrations of the reacting gases stay the same, so Q still equals K. At constant total pressure the volume grows, which dilutes the mixture and acts like a pressure drop.
Why does the calculator need equilibrium concentrations?
K is derived from them as [C]^c [D]^d / ([A]^a [B]^b), so you do not need to look up K separately. It also gives the starting composition for the new equilibrium, which is found by solving for the extent of reaction that brings Q back to K.
What is the extent of reaction in the results?
It is the amount, in mol/L, of the reaction as written that proceeds to restore equilibrium. A positive value means reactants are consumed and products form, and a negative value means the reverse. Each concentration changes by its coefficient times this extent.
Is the new equilibrium always a full reversal of the disturbance?
No. The system only partly offsets the change. After adding reactant, some of it remains and the product amounts rise, but the new equilibrium never returns to the exact old concentrations unless the stress is removed.