Kirchhoff Law Temperature-Dependent Enthalpy Calculator

Shift a reaction enthalpy from T1 to T2 with Kirchhoff's law, using a constant dCp or a heat capacity polynomial.

🌡️ Kirchhoff Law Temperature-Dependent Enthalpy Calculator
Reaction enthalpy at T1 (dH)
kJ/mol
Heat capacity change (dCp)
J/(mol K)
Reference temperature (T1)
K
Target temperature (T2)
K
Reaction enthalpy at T1 (dH)
kJ/mol
Reference temperature (T1)
K
Target temperature (T2)
K
Coefficient a
J/(mol K)
Coefficient b
J/(mol K2)
Coefficient c (illustrative)
J/(mol K3)
Reaction enthalpy at T2
—
Change from T1 to T2
—
Temperature interval
—
Slope d(dH)/dT = dCp
—
Shift as percent of dH(T1)
—
Type at T2
—

Reaction enthalpy at T2
—
Integral of dCp dT
—
dCp at T1
—
dCp at T2
—
Mean dCp over the interval
—
Type at T2
—

🌡️ What is Kirchhoff's Law in Thermochemistry?

Kirchhoff's law of thermochemistry tells you how the enthalpy of a reaction changes with temperature. Tables list standard reaction enthalpies at 298.15 K, but real reactors, engines and furnaces run far from that temperature. The law links the two: the rate at which the reaction enthalpy changes with temperature equals the difference between the heat capacity of the products and the heat capacity of the reactants, written dCp. Integrate dCp from the reference temperature to the target temperature, add it to the tabulated enthalpy, and you have the enthalpy where you need it.

Chemical engineers use it to estimate the heat released in ammonia synthesis at 500 K instead of 298 K, to correct combustion enthalpies for hot flue gas, and to build energy balances for reactors. Physical chemists use it to put calorimetric data taken at one temperature on a common footing with data from another. It is also the bridge that lets you apply Hess's law when individual steps are known at different temperatures, since Hess's law only holds when every enthalpy refers to the same temperature.

A frequent misconception is that reaction enthalpy is a fixed constant of the reaction. It is not. It drifts with temperature in proportion to dCp, and the drift can be significant over a few hundred kelvin. Another is that the sign of dCp equals the sign of the enthalpy, which is false: dCp tells you the slope of dH against T, not the value of dH. A reaction can be exothermic at every temperature while becoming less exothermic as it is heated, which is exactly what happens with a negative dCp.

This calculator offers two modes. The constant mode assumes dCp does not change over the interval and applies dH(T2) = dH(T1) + dCp (T2 - T1). The polynomial mode accepts the common form dCp = a + bT + cT2 and integrates it exactly, so it stays accurate across wide ranges when you have fitted coefficients. Both plot the enthalpy against temperature so you can see the slope and check that your input temperatures make sense. Phase changes are not handled automatically, so add the enthalpy of any phase transition yourself.

📐 Formula

dH(T2)  =  dH(T1)  +  ∫ dCp dT  =  dH(T1)  +  dCp (T2 − T1)
dH(T1) = known reaction enthalpy at the reference temperature (kJ/mol)
dH(T2) = reaction enthalpy at the target temperature (kJ/mol)
dCp = Σ Cp(products) − Σ Cp(reactants), constant here (J/(mol K))
T1, T2 = reference and target temperatures (K)
Example: dH = −92.2 kJ/mol at 298.15 K, dCp = −45.3 J/(mol K), T2 = 500 K gives dH(500 K) = -101.3 kJ/mol
dCp(T)  =  a + bT + cT2  ⇒  ∫ dCp dT  =  a(T2 − T1) + (b/2)(T22 − T12) + (c/3)(T23 − T13)
a, b, c = polynomial coefficients in J/(mol K), J/(mol K2) and J/(mol K3)
Units: the integral is in J/mol, so divide by 1000 before adding it to dH in kJ/mol
Validity: the coefficients hold only inside the temperature range of the data they were fitted to
Example: a = −50, b = 0.04, c = −0.00001, T1 = 298.15 K, T2 = 600 K gives an integral of -10.30 kJ/mol

📖 How to Use This Calculator

Two modes

1
Choose a mode - Pick Constant dCp for a single heat capacity change over the interval, or Polynomial to integrate dCp = a + bT + cT2.
2
Enter the enthalpy and temperatures - Type the reaction enthalpy at T1 in kJ/mol, then T1 and T2 in kelvin. Add dCp in J/(mol K), or the three coefficients a, b and c.
3
Read the enthalpy at T2 and the chart - The primary box is the enthalpy at T2. The other boxes show the shift, the interval, the heat capacities and whether the reaction is exothermic or endothermic at T2. The chart marks T1 and T2.
4
Check the validity range - If a species changes phase between T1 and T2, or the interval exceeds the fitted range of your coefficients, split the calculation or use better data.

💡 Example Calculations

Example 1 - Ammonia synthesis at 500 K

N2 + 3 H2 to 2 NH3: dH(298.15 K) = -92.2 kJ/mol, dCp = -45.3 J/(mol K) (approximate), T2 = 500 K

1
Temperature interval T2 − T1 = 500 − 298.15 = 201.85 K.
2
Shift = dCp × interval / 1000 = (−45.3 × 201.85) / 1000 = -9.144 kJ/mol.
3
dH(500 K) = −92.2 + (-9.144) = -101.3 kJ/mol, which is 9.92 percent more exothermic.
dH(500 K) = -101.3 kJ/mol
Try this example →

Example 2 - Enthalpy of vaporization of water at its boiling point

H2O(l) to H2O(g): dH(298.15 K) = 44.0 kJ/mol, dCp = 33.6 - 75.3 = -41.7 J/(mol K) (approximate), T2 = 373.15 K

1
Interval = 373.15 − 298.15 = 75.00 K.
2
Shift = (−41.7 × 75.00) / 1000 = -3.128 kJ/mol.
3
dH(373.15 K) = 44.0 + (-3.128) = 40.87 kJ/mol, close to the measured value of about 40.7 kJ/mol at the normal boiling point.
dH(373.15 K) = 40.87 kJ/mol
Try this example →

Example 3 - Polynomial heat capacity change

dH(298.15 K) = -92.2 kJ/mol, dCp = -50 + 0.04 T - 0.00001 T^2 (illustrative), T2 = 600 K

1
a term: −50 × (600 − 298.15) / 1000 = -15.09 kJ/mol.
2
b term: (0.04 / 2) × (6002 − 298.152) / 1000 = 5.422 kJ/mol.
3
c term: (−0.00001 / 3) × (6003 − 298.153) / 1000 = -0.6317 kJ/mol, so the integral is -10.30 kJ/mol and dH(600 K) = -102.5 kJ/mol.
dH(600 K) = -102.5 kJ/mol, dCp(T1) = -38.96 J/(mol K), dCp(T2) = -29.60 J/(mol K)
Try this example →

Example 4 - Cooling below the reference temperature

2 CO + O2 to 2 CO2: dH(298.15 K) = -566.0 kJ/mol, dCp = -13.4 J/(mol K) (approximate), T2 = 250 K

1
Interval = 250 − 298.15 = -48.15 K, negative because the system is cooled.
2
Shift = (−13.4 × (-48.15)) / 1000 = +0.6452 kJ/mol.
3
dH(250 K) = −566.0 + 0.6452 = -565.4 kJ/mol: slightly less exothermic when cold.
dH(250 K) = -565.4 kJ/mol
Try this example →

❓ Frequently Asked Questions

What is Kirchhoff's law in thermochemistry?+
Kirchhoff's law says that the temperature derivative of a reaction enthalpy equals the heat capacity change of the reaction, d(dH)/dT = dCp. Integrating it from T1 to T2 gives dH(T2) = dH(T1) + integral of dCp dT, which lets you move a tabulated 298 K enthalpy to any other temperature.
How do you calculate reaction enthalpy at a different temperature?+
Compute dCp as the sum of product heat capacities minus the sum of reactant heat capacities, each multiplied by its stoichiometric coefficient. For a constant dCp the shift is dCp x (T2 - T1). Add that shift, converted to kJ/mol, to the known enthalpy at T1.
What is the Kirchhoff equation for a constant dCp?+
dH(T2) = dH(T1) + dCp (T2 - T1). With dH(298.15 K) = -92.2 kJ/mol and dCp = -45.3 J/(mol K) for ammonia synthesis, the enthalpy at 500 K is -92.2 + (-45.3 x 201.85 / 1000) = -101.34 kJ/mol.
How do I use a heat capacity polynomial a + bT + cT^2?+
Integrate term by term: a(T2 - T1) + (b/2)(T2^2 - T1^2) + (c/3)(T2^3 - T1^3). The result is in J/mol when a, b and c are in J/(mol K), J/(mol K^2) and J/(mol K^3), so divide by 1000 for kJ/mol. The polynomial mode does exactly this.
Why does the reaction enthalpy change with temperature?+
Reactants and products warm up by different amounts of energy because their heat capacities differ. If the products have a larger total heat capacity, heating them absorbs more energy and the reaction becomes more endothermic as T rises. If they have a smaller one, the enthalpy falls.
When is a constant dCp a good approximation?+
A constant dCp works well when the temperature range is modest, roughly 100 K or less, and when no species changes phase. Over larger ranges the heat capacities themselves vary, so the polynomial mode with fitted coefficients gives a more reliable answer.
What happens if a species changes phase between T1 and T2?+
The simple integral no longer holds, because a phase transition adds its own enthalpy of fusion or vaporization and switches the heat capacity to a different phase value. Split the path into steps, applying Kirchhoff's law in each phase and adding the transition enthalpy at its transition temperature.
Does Kirchhoff's law apply to internal energy as well?+
Yes, in the analogous form d(dU)/dT = dCv, where dCv is the change in constant-volume heat capacity. This calculator works with enthalpy and the constant-pressure heat capacity Cp, which is the usual case for reactions in open vessels.
What units does the calculator use?+
Enthalpy is in kJ/mol, temperature in kelvin, dCp in J/(mol K), the polynomial coefficients b and c in J/(mol K^2) and J/(mol K^3). Convert Celsius by adding 273.15 before typing a temperature.
Can T2 be lower than T1?+
Yes. The integral then runs backward and the sign of the shift flips. For CO oxidation, with dH = -566.0 kJ/mol at 298.15 K and dCp = -13.4 J/(mol K), cooling to 250 K gives -566.0 + (-13.4 x (-48.15) / 1000) = -565.355 kJ/mol.
How accurate are the example heat capacities?+
The dCp values on this page come from rounded textbook Cp values near 298 K and are approximate. Use values from NIST or the CRC Handbook for real work, and use the polynomial mode when you have fitted coefficients for your species.

📚 Sources and Notes

The relation d(dH)/dT = dCp and its integrated forms follow the treatment in the LibreTexts page on Kirchhoff's law and the Wikipedia article on the standard enthalpy of reaction. The heat capacities and reaction enthalpies in the examples are rounded textbook values, approximate and illustrative; use NIST or CRC Handbook data for precise work. The polynomial coefficients in the third example are illustrative, not fitted to a real reaction.

See also the enthalpy calculator, the Gibbs free energy of reaction calculator and the van't Hoff equation calculator.

What is Kirchhoff's law in thermochemistry?

Kirchhoff's law says that the temperature derivative of a reaction enthalpy equals the heat capacity change of the reaction, d(dH)/dT = dCp. Integrating it from T1 to T2 gives dH(T2) = dH(T1) + integral of dCp dT, which lets you move a tabulated 298 K enthalpy to any other temperature.

How do you calculate reaction enthalpy at a different temperature?

Compute dCp as the sum of product heat capacities minus the sum of reactant heat capacities, each multiplied by its stoichiometric coefficient. For a constant dCp the shift is dCp x (T2 - T1). Add that shift, converted to kJ/mol, to the known enthalpy at T1.

What is the Kirchhoff equation for a constant dCp?

dH(T2) = dH(T1) + dCp (T2 - T1). With dH(298.15 K) = -92.2 kJ/mol and dCp = -45.3 J/(mol K) for ammonia synthesis, the enthalpy at 500 K is -92.2 + (-45.3 x 201.85 / 1000) = -101.34 kJ/mol.

How do I use a heat capacity polynomial a + bT + cT^2?

Integrate term by term: a(T2 - T1) + (b/2)(T2^2 - T1^2) + (c/3)(T2^3 - T1^3). The result is in J/mol when a, b and c are in J/(mol K), J/(mol K^2) and J/(mol K^3), so divide by 1000 for kJ/mol. The polynomial mode does exactly this.

Why does the reaction enthalpy change with temperature?

Reactants and products warm up by different amounts of energy because their heat capacities differ. If the products have a larger total heat capacity, heating them absorbs more energy and the reaction becomes more endothermic as T rises. If they have a smaller one, the enthalpy falls.

When is a constant dCp a good approximation?

A constant dCp works well when the temperature range is modest, roughly 100 K or less, and when no species changes phase. Over larger ranges the heat capacities themselves vary, so the polynomial mode with fitted coefficients gives a more reliable answer.

What happens if a species changes phase between T1 and T2?

The simple integral no longer holds, because a phase transition adds its own enthalpy of fusion or vaporization and switches the heat capacity to a different phase value. Split the path into steps, applying Kirchhoff's law in each phase and adding the transition enthalpy at its transition temperature.

Does Kirchhoff's law apply to internal energy as well?

Yes, in the analogous form d(dU)/dT = dCv, where dCv is the change in constant-volume heat capacity. This calculator works with enthalpy and the constant-pressure heat capacity Cp, which is the usual case for reactions in open vessels.

What units does the calculator use?

Enthalpy is in kJ/mol, temperature in kelvin, dCp in J/(mol K), the polynomial coefficients b and c in J/(mol K^2) and J/(mol K^3). Convert Celsius by adding 273.15 before typing a temperature.

Can T2 be lower than T1?

Yes. The integral then runs backward and the sign of the shift flips. For CO oxidation, with dH = -566.0 kJ/mol at 298.15 K and dCp = -13.4 J/(mol K), cooling to 250 K gives -566.0 + (-13.4 x (-48.15) / 1000) = -565.355 kJ/mol.

How accurate are the example heat capacities?

The dCp values on this page come from rounded textbook Cp values near 298 K and are approximate. Use values from NIST or the CRC Handbook for real work, and use the polynomial mode when you have fitted coefficients for your species.