Rubber Elasticity (Neo-Hookean) Stress Calculator

Compute neo-Hookean rubber stress against stretch and link the shear modulus to crosslink density and chain length between crosslinks.

🎈 Rubber Elasticity (Neo-Hookean) Stress Calculator
Deformation
Shear modulus (G)
MPa
Stretch ratio (λ)
Known quantity
Shear modulus (G)
MPa
Molar mass between crosslinks (Mc)
g/mol
Temperature (T)
K
Density (ρ, illustrative)
g/cm³
Engineering (nominal) stress
—
True (Cauchy) stress
—
Young modulus E ≈ 3G
—
Engineering strain
—
Small-strain slope
—
Stress / linear estimate
—

Molar mass between crosslinks Mc
—
Shear modulus G
—
Mc
—
Strand density G/RT
—
Strands per volume G/kT
—
Young modulus E ≈ 3G
—

🎈 What is Neo-Hookean Rubber Elasticity?

Rubber elasticity is the ability of a lightly crosslinked polymer network to stretch to several times its length and spring back. Unlike a metal or a glass, whose elasticity comes from bond stretching, the elasticity of rubber is mainly entropic. A flexible chain between two crosslinks can adopt a huge number of coiled shapes, and stretching it forces the chain into a smaller set of aligned shapes. The loss of entropy produces a restoring force proportional to the absolute temperature, which is why a stretched rubber band held at fixed length pulls harder when it is warmed.

The statistical theory of this behavior, due to Kuhn, Wall, Flory and Treloar, treats each strand as a Gaussian chain and assumes the network junctions move affinely with the imposed deformation. The result is the neo-Hookean model, a one-parameter law in which the strain energy is W = (G/2)(λ12 + λ22 + λ32 − 3). The single constant is the shear modulus G = n k T, where n is the number of elastic strands per unit volume. Written per mole, G = ρ R T / Mc, so the modulus rises with the crosslink density and falls as the chain length between crosslinks Mc grows.

For a rubber that keeps its volume (incompressible), the stress follows from the stretch ratios alone. In uniaxial loading the engineering stress is G(λ − 1/λ2), which is the force per original area, while the true stress G(λ2 − 1/λ) uses the current area. Equibiaxial stretching and pure shear follow the same recipe with a different constraint on the third stretch. At small strain all three reduce to Hooke's law with slopes 3G, 6G and 4G, which is why the Young modulus of rubber is about 3G.

Use this calculator to estimate how much stress a rubber part carries at a given stretch, to convert a measured modulus to a crosslink density and a chain length between crosslinks, or to check how far the stress departs from linear elasticity. It is an idealized model: it has no strain stiffening, so it works best up to moderate stretch. For the next level of detail see the Mooney-Rivlin model calculator, and for the general modulus relations see the shear modulus calculator.

📐 Formula

s  =  G (λ − λ−2)    σ  =  G (λ2 − λ−1)
s = engineering (nominal) stress, force per original area; σ = true (Cauchy) stress = s λ
G = shear modulus; λ = stretch ratio, current length over original length
Equibiaxial: s = G (λ − λ−5), σ = G (λ2 − λ−4)
Pure shear: s = G (λ − λ−3), σ = G (λ2 − λ−2)
Example: G = 0.4 MPa and λ = 2 give s = 0.70 MPa and σ = 1.40 MPa
G  =  n k T  =  ρ R T ÷ Mc    E ≈ 3 G
n = elastic strands per unit volume; k = Boltzmann constant 1.380649e-23 J/K
R = gas constant 8.314462618 J/(mol K); T = absolute temperature (K)
ρ = polymer density; Mc = molar mass of a strand between crosslinks
Strand density: ν = G / R T in mol/m³ and n = G / k T in strands per m³
Example: G = 0.4 MPa, ρ = 0.92 g/cm³, T = 298.15 K give Mc = 5,702 g/mol

📖 How to Use This Calculator

Two modes

1
Choose a mode - Pick Stress vs stretch for neo-Hookean stress, or Crosslink network to link the modulus to Mc and strand density.
2
Enter the parameters - Type the shear modulus in MPa and the stretch ratio and pick a deformation type, or enter the temperature, density and either G or Mc.
3
Read the results - Read the nominal and true stress and the small-strain comparison, or the network quantities and the incompressible Young modulus.
4
Check the chart - The dashed green guide marks your input on the stress-stretch curve or on the G against Mc line.

💡 Example Calculations

Example 1 - Uniaxial stretch to twice the length

G = 0.4 MPa (illustrative soft rubber), λ = 2, uniaxial

1
Engineering stress s = 0.4 × (2 - 1/4) = 0.4 × 1.75 = 0.7000 MPa.
2
True stress σ = 0.4 × (4 - 1/2) = 1.400 MPa, equal to s × 2.
3
The small-strain slope is 3G = 1.2 MPa, so the linear estimate at 100 percent strain is 1.2 MPa and the neo-Hookean stress is 0.5833 of it.
s = 0.7000 MPa, σ = 1.400 MPa
Try this example →

Example 2 - Equibiaxial stretch (inflating a membrane)

G = 0.4 MPa, λ = 1.5, equibiaxial

1
λ-5 = 1 / 7.59375 = 0.13169.
2
s = 0.4 × (1.5 - 0.13169) = 0.5473 MPa.
3
σ = 0.4 × (2.25 - 0.19753) = 0.8210 MPa, and the small-strain slope is 6G = 2.4 MPa.
s = 0.5473 MPa, σ = 0.8210 MPa
Try this example →

Example 3 - Pure shear of a thin sheet

G = 0.5 MPa, λ = 3, pure shear

1
λ-3 = 1/27 = 0.03704.
2
s = 0.5 × (3 - 0.03704) = 1.481 MPa.
3
σ = 0.5 × (9 - 1/9) = 4.444 MPa, and the small-strain slope is 4G = 2 MPa.
s = 1.481 MPa, σ = 4.444 MPa
Try this example →

Example 4 - Mc from a measured modulus

G = 0.4 MPa, ρ = 0.92 g/cm³ (illustrative), T = 298.15 K

1
R T = 8.314463 × 298.15 = 2478.96 J/mol.
2
Mc = (0.92 × 106 × 2478.96) / (0.4 × 106) = 5,702 g/mol.
3
Strand density G/RT = 161.4 mol/m³, which is 9.717e25 strands per m³, and E ≈ 3G = 1.2 MPa.
Mc = 5,702 g/mol, strand density = 161.4 mol/m³
Try this example →

Example 5 - Modulus from a chain length between crosslinks

Mc = 10,000 g/mol, ρ = 0.92 g/cm³, T = 298.15 K

1
Strand density = 0.92 g/cm³ / 10,000 g/mol = 92.00 mol/m³.
2
G = 92.00 × 2478.96 = 0.2281 MPa.
3
E ≈ 3G = 0.6842 MPa.
G = 0.2281 MPa, E ≈ 0.6842 MPa
Try this example →

❓ Frequently Asked Questions

What is the neo-Hookean model?+
The neo-Hookean model is a one-parameter hyperelastic law derived from the statistical mechanics of a crosslinked network of Gaussian chains. Its strain energy is W = (G/2)(I1 - 3), where G is the shear modulus, and it describes the large-strain behavior of rubber-like solids.
What is the formula for uniaxial stress in a neo-Hookean solid?+
For an incompressible solid stretched by lambda, the true stress is sigma = G (lambda^2 - 1/lambda) and the engineering stress is s = G (lambda - 1/lambda^2). With G = 0.4 MPa and lambda = 2, s = 0.70 MPa and sigma = 1.40 MPa.
What is the difference between true stress and engineering stress?+
Engineering (nominal) stress uses the original cross-section, true (Cauchy) stress uses the current one. For an incompressible rubber the true stress equals the engineering stress multiplied by the stretch lambda.
How is the shear modulus related to crosslink density?+
The statistical theory gives G = n k T, where n is the number of elastic strands per unit volume. In molar form G = rho R T / Mc, with Mc the molar mass between crosslinks. A higher crosslink density means a stiffer rubber.
How do you calculate Mc from the modulus?+
Use Mc = rho R T / G. For G = 0.4 MPa, rho = 0.92 g/cm3 and T = 298.15 K, Mc = 0.92e6 x 8.3145 x 298.15 / 0.4e6 = 5,702 g/mol, and the strand density is G / RT = 161.4 mol/m3.
How is Young modulus related to shear modulus for rubber?+
Rubber is nearly incompressible, so the Poisson ratio is close to 0.5 and E = 2G(1 + nu) is about 3G. A rubber with G = 0.4 MPa has E near 1.2 MPa.
How do equibiaxial and pure shear stresses differ from uniaxial?+
The same modulus gives different stress paths. Nominal stress is G (lambda - lambda^-2) for uniaxial, G (lambda - lambda^-5) for equibiaxial and G (lambda - lambda^-3) for pure shear. Small-strain slopes are 3G, 6G and 4G respectively.
Why does the stress in rubber depend on temperature?+
Rubber elasticity is mostly entropic. Stretching reduces the number of chain conformations, and the restoring force scales with k T, so a stretched rubber at fixed length pulls harder when heated, unlike a metal.
When does the neo-Hookean model fail?+
It ignores finite chain extensibility, so it underpredicts stress at large stretch, and it misses the extra softening and stiffening seen in uniaxial against biaxial data. The Mooney-Rivlin model adds a second parameter for this.
What is a typical shear modulus of rubber?+
Soft elastomers fall roughly between 0.2 and 2 MPa (illustrative range). Gels are far softer at kPa levels and glassy polymers are 1000 times stiffer, so the 0.4 MPa default here is only an illustrative soft rubber value.

📚 Sources and Notes

The entropic origin of the restoring force and the affine Gaussian network assumptions follow the Wikipedia article on rubber elasticity, and the neo-Hookean model as an incompressible hyperelastic law follows the neo-Hookean solid article. The stress expressions follow from the incompressible Cauchy stress Gλi2 minus a pressure fixed by zero stress in the free direction. The 0.4 MPa modulus, the 0.92 g/cm³ density and the quoted modulus ranges are illustrative values, not measured data.

See also the polymer physics calculators and the Poisson's ratio calculator.

What is the neo-Hookean model?

The neo-Hookean model is a one-parameter hyperelastic law derived from the statistical mechanics of a crosslinked network of Gaussian chains. Its strain energy is W = (G/2)(I1 - 3), where G is the shear modulus, and it describes the large-strain behavior of rubber-like solids.

What is the formula for uniaxial stress in a neo-Hookean solid?

For an incompressible solid stretched by lambda, the true stress is sigma = G (lambda^2 - 1/lambda) and the engineering stress is s = G (lambda - 1/lambda^2). With G = 0.4 MPa and lambda = 2, s = 0.70 MPa and sigma = 1.40 MPa.

What is the difference between true stress and engineering stress?

Engineering (nominal) stress uses the original cross-section, true (Cauchy) stress uses the current one. For an incompressible rubber the true stress equals the engineering stress multiplied by the stretch lambda.

How is the shear modulus related to crosslink density?

The statistical theory gives G = n k T, where n is the number of elastic strands per unit volume. In molar form G = rho R T / Mc, with Mc the molar mass between crosslinks. A higher crosslink density means a stiffer rubber.

How do you calculate Mc from the modulus?

Use Mc = rho R T / G. For G = 0.4 MPa, rho = 0.92 g/cm3 and T = 298.15 K, Mc = 0.92e6 x 8.3145 x 298.15 / 0.4e6 = 5,702 g/mol, and the strand density is G / RT = 161.4 mol/m3.

How is Young modulus related to shear modulus for rubber?

Rubber is nearly incompressible, so the Poisson ratio is close to 0.5 and E = 2G(1 + nu) is about 3G. A rubber with G = 0.4 MPa has E near 1.2 MPa.

How do equibiaxial and pure shear stresses differ from uniaxial?

The same modulus gives different stress paths. Nominal stress is G (lambda - lambda^-2) for uniaxial, G (lambda - lambda^-5) for equibiaxial and G (lambda - lambda^-3) for pure shear. Small-strain slopes are 3G, 6G and 4G respectively.

Why does the stress in rubber depend on temperature?

Rubber elasticity is mostly entropic. Stretching reduces the number of chain conformations, and the restoring force scales with k T, so a stretched rubber at fixed length pulls harder when heated, unlike a metal.

When does the neo-Hookean model fail?

It ignores finite chain extensibility, so it underpredicts stress at large stretch, and it misses the extra softening and stiffening seen in uniaxial against biaxial data. The Mooney-Rivlin model adds a second parameter for this.

What is a typical shear modulus of rubber?

Soft elastomers fall roughly between 0.2 and 2 MPa (illustrative range). Gels are far softer at kPa levels and glassy polymers are 1000 times stiffer, so the 0.4 MPa default here is only an illustrative soft rubber value.