Polymer Diffusion Coefficient Calculator

Compare the Rouse, Zimm and reptation diffusion coefficients of a polymer chain and convert between hydrodynamic radius and D.

🌀 Polymer Diffusion Coefficient Calculator
Temperature (T)
K
Solvent viscosity (ηs)
mPa s
Assumed Rg/Rh ratio (illustrative)
Segments (N)
Segment length (b)
nm
Entanglement length (Ne, illustrative)
Friction factor (f)
Known quantity
Hydrodynamic radius (Rh)
nm
Diffusion coefficient (D)
µm²/s
Rouse D
—
Rouse D (cm²/s)
—
Zimm D
—
Zimm D (cm²/s)
—
Reptation D
—
Reptation D (cm²/s)
—
Bead friction (ζ)
—
Hydrodynamic radius (Rh)
—

Diffusion coefficient (D)
—
D (µm²/s)
—
D (cm²/s)
—
Hydrodynamic radius (Rh)
—
Implied Rg
—
rms 1D shift in 1 s
—

🌀 What is the Polymer Diffusion Coefficient?

The polymer diffusion coefficient D measures how fast a whole polymer chain wanders through its surroundings. It is defined from the mean square displacement of the chain centre of mass, which grows as 6 D t in three dimensions. Small molecules in water diffuse with D near 10-9 m2/s, whereas a long polymer in solution is a thousand times slower and a long chain in an entangled melt can be slower still by many orders of magnitude. Because D depends so strongly on chain length, measuring it is a standard route to molar mass, chain architecture and the degree of entanglement.

Three classical models describe how D depends on the number of segments N. The Rouse model treats the chain as N beads joined by springs, each bead feeling its own friction ζ and no flow coupling between beads. The friction simply adds up, giving D = k T / (N ζ) and a scaling D ∝ N-1. The Zimm model keeps the solvent hydrodynamic interaction: the solvent inside the coil moves with it, so the coil drags like a Stokes sphere and D = k T / (6 π ηs Rh). Since Rh grows as Nν this gives D ∝ N-ν, or N-1/2 for an ideal chain. The reptation model of de Gennes and Doi and Edwards applies to entangled melts, where each chain is confined to a tube formed by its neighbours and can only slide along its own contour. This gives D = DRouse / (3 Z) with Z = N / Ne, and therefore D ∝ N-2.

Which model applies depends on the environment, not just on the chain. Dilute solutions follow Zimm, short unentangled melts follow Rouse, and long melts follow reptation. This calculator evaluates all three from the same chain so you can see how fast the curves separate as N grows, and it adds a Stokes-Einstein mode that converts directly between a hydrodynamic radius and D. It differs from the Einstein-Stokes diffusion coefficient calculator, which handles a rigid particle of given radius, by building the chain size and friction from N and b and by covering the Rouse and reptation scalings. For the chain size itself see the radius of gyration calculator, and for the tube picture see the reptation time and tube length calculator.

📐 Formula

DRouse  =  k T ÷ (N ζ)   |   DZimm  =  k T ÷ (6 π ηs Rh)   |   Drep  =  DRouse ÷ (3 Z)
k = Boltzmann constant, 1.380649 × 10-23 J/K
T = absolute temperature (K)
N = number of segments; b = segment length (m)
ζ = friction of one segment = f × 3 π ηs b (Stokes bead of diameter b; illustrative)
Rh = Rg / (Rg/Rh) with Rg = b √(N/6) for an ideal chain
Z = N / Ne, the number of entanglement lengths; reptation is used only for Z ≥ 1
Example: N = 1000, b = 1 nm, T = 298 K, ηs = 1 mPa s gives ζ = 9.425 pN s/m and DRouse = 4.365 × 10-13 m2/s
Rh  =  k T ÷ (6 π η D)
Rh = hydrodynamic radius (m); the Stokes-Einstein relation solved for the radius
η = solvent viscosity (Pa s); 1 mPa s = 10-3 Pa s
D = translational diffusion coefficient (m2/s)
Example: D = 100 µm2/s in water-like solvent at 298 K gives Rh = 2.183 nm

📖 How to Use This Calculator

Two modes

1
Set the shared inputs - Enter the absolute temperature in kelvin, the solvent viscosity in mPa s (water at 25 °C is about 0.89) and the Rg/Rh ratio. The ratio of 1.5 is an illustrative value for a flexible coil.
2
Choose Chain regimes - Type the number of segments N, the segment length b in nm, the entanglement length Ne in segments and a friction factor. A factor of 1 means a Stokes bead of diameter b.
3
Or choose Stokes-Einstein - Select whether Rh or D is known and type its value. The calculator returns the other one in nm, m²/s, cm²/s and µm²/s.
4
Read D and the chart - Compare the three regimes in the result boxes and on the log-log chart, where your chain is marked with a dashed guide, and note that reptation is blank when N is below Ne.

💡 Example Calculations

Example 1 - An unentangled to entangled chain of 1000 segments

N = 1000, b = 1 nm, Ne = 100, T = 298 K, ηs = 1 mPa s, f = 1, Rg/Rh = 1.5

1
Bead friction ζ = 3 π × 0.001 × 10-9 = 9.425 pN s/m, so DRouse = k T / (N ζ) = 4.365 × 10-13 m2/s.
2
Rg = 1 × √(1000/6) = 12.91 nm, so Rh = 12.91 / 1.5 = 8.607 nm and DZimm = k T / (6 π ηs Rh) = 2.536 × 10-11 m2/s.
3
Z = 1000 / 100 = 10, so Drep = DRouse / 30 = 1.455 × 10-14 m2/s.
Rouse 4.365e-13 m²/s, Zimm 2.536e-11 m²/s, reptation 1.455e-14 m²/s
Try this example →

Example 2 - Ten times longer chain

N = 10,000, other inputs as in Example 1

1
DRouse falls by a factor of 10 to 4.365 × 10-14 m2/s because it scales as N-1.
2
DZimm falls by √10 = 3.162 to 8.020 × 10-12 m2/s, with Rh = 27.22 nm.
3
Z = 100, so Drep = 1.455 × 10-16 m2/s, which is 100 times smaller than at N = 1000 since it scales as N-2.
Reptation 1.455e-16 m²/s (1.455e-12 cm²/s), Rh = 27.22 nm
Try this example →

Example 3 - Diffusion of a 5 nm particle or coil

Rh = 5 nm, T = 298 K, η = 1 mPa s

1
D = k T / (6 π η Rh) = 4.114 × 10-21 / (6 π × 0.001 × 5 × 10-9) = 4.365 × 10-11 m2/s.
2
That is 43.65 µm2/s or 4.365 × 10-7 cm2/s, and the implied Rg with the ratio 1.5 is 7.500 nm.
3
The rms one-dimensional displacement in 1 s is √(2 D t) = 9.344 µm.
D = 4.365e-11 m²/s = 43.65 µm²/s
Try this example →

Example 4 - Hydrodynamic radius from a measured D

D = 100 µm2/s, T = 298 K, η = 1 mPa s

1
Rh = k T / (6 π η D) = 4.114 × 10-21 / (6 π × 0.001 × 10-10) = 2.183 nm.
2
The implied Rg is 1.5 × 2.183 = 3.274 nm, and the rms one-dimensional shift in 1 s is 14.14 µm.
Rh = 2.183 nm, Rg = 3.274 nm
Try this example →

❓ Frequently Asked Questions

What is the polymer diffusion coefficient?+
It is the translational diffusion coefficient D of a polymer chain, defined by the mean square displacement of its centre of mass, <r^2> = 6 D t in three dimensions. It falls as the chain gets longer because the chain drags more solvent or is hindered by neighbouring chains.
What is the Rouse diffusion coefficient formula?+
D = k T / (N zeta), where k is Boltzmann's constant, T the absolute temperature, N the number of segments and zeta the friction coefficient of one segment. Hydrodynamic interaction is ignored, so D is inversely proportional to N.
What is the Zimm diffusion coefficient formula?+
The chain behaves like a Stokes sphere, D = k T / (6 pi eta_s Rh), with solvent viscosity eta_s and hydrodynamic radius Rh. For an ideal chain Rh is proportional to sqrt(N), so D falls as N^-1/2. In a good solvent the exponent is about -0.588.
How does the reptation diffusion coefficient scale with chain length?+
In the Doi-Edwards tube model D = D_Rouse / (3 Z) with Z = N/Ne, which gives D proportional to N^-2. Experiments on entangled melts find a slightly steeper dependence, close to N^-2.3, because of effects the simple tube model leaves out.
Why does the Zimm model give a larger D than the Rouse model?+
In the Zimm model the solvent moves with the coil, so the whole chain drags a single hydrodynamic volume instead of N independent beads. The friction grows only as sqrt(N) rather than N, so long chains diffuse much faster than free-draining Rouse beads in the same solvent.
When should I use the Rouse, Zimm or reptation result?+
Use Zimm for dilute solutions, Rouse for unentangled melts and semidilute solutions at short lengths where hydrodynamics is screened, and reptation for entangled melts with N above the entanglement length. The calculator shows all three so you can compare scalings.
How do I get the hydrodynamic radius from D?+
Rearrange Stokes-Einstein, Rh = k T / (6 pi eta D). With D = 100 um^2/s in water at 298 K and 1 mPa s the result is Rh = 2.18 nm. Use the Stokes-Einstein mode and select D as the known quantity.
What units does the calculator use for diffusion coefficients?+
Results are given in m^2/s and cm^2/s, and the Stokes-Einstein mode also shows um^2/s. One cm^2/s equals 10^-4 m^2/s and one um^2/s equals 10^-12 m^2/s, so 4.365e-11 m^2/s is 4.365e-7 cm^2/s or 43.65 um^2/s.
How is this different from the Einstein-Stokes biophysics calculator?+
That page treats a rigid particle of known radius. This one starts from the chain length N and segment length b, builds Rg and Rh for a flexible coil, and adds the Rouse and reptation scalings with their different dependence on N.
What does the Rg/Rh ratio do here?+
It converts the chain size into a hydrodynamic radius, Rh = Rg / ratio. For a flexible coil the ratio is about 1.5, a hard sphere gives 0.775. The default 1.5 is an illustrative value, so replace it with a measurement when you have one.

📚 Sources and Notes

The Rouse bead-spring picture and its extension by Zimm are summarised in the Wikipedia article on the Rouse model. The N-1 and N-1/2 scalings follow the Oxford polymer dynamics lecture notes, and the tube model discussion follows these tube model lecture notes. The explicit form D = DRouse/(3Z) is the standard Doi-Edwards expression, quoted from the textbook and not checked against an online source here. The Stokes bead friction, the Rg/Rh ratio of 1.5 and the entanglement length Ne = 100 are illustrative defaults, not measured constants, and reptation prefactors differ between definitions by factors near 1.6.

See also the polymer physics calculators and the Einstein-Stokes diffusion coefficient calculator.

What is the polymer diffusion coefficient?

It is the translational diffusion coefficient D of a polymer chain, defined by the mean square displacement of its centre of mass, <r^2> = 6 D t in three dimensions. It falls as the chain gets longer because the chain drags more solvent or is hindered by neighbouring chains.

What is the Rouse diffusion coefficient formula?

D = k T / (N zeta), where k is Boltzmann's constant, T the absolute temperature, N the number of segments and zeta the friction coefficient of one segment. Hydrodynamic interaction is ignored, so D is inversely proportional to N.

What is the Zimm diffusion coefficient formula?

The chain behaves like a Stokes sphere, D = k T / (6 pi eta_s Rh), with solvent viscosity eta_s and hydrodynamic radius Rh. For an ideal chain Rh is proportional to sqrt(N), so D falls as N^-1/2. In a good solvent the exponent is about -0.588.

How does the reptation diffusion coefficient scale with chain length?

In the Doi-Edwards tube model D = D_Rouse / (3 Z) with Z = N/Ne, which gives D proportional to N^-2. Experiments on entangled melts find a slightly steeper dependence, close to N^-2.3, because of effects the simple tube model leaves out.

Why does the Zimm model give a larger D than the Rouse model?

In the Zimm model the solvent moves with the coil, so the whole chain drags a single hydrodynamic volume instead of N independent beads. The friction grows only as sqrt(N) rather than N, so long chains diffuse much faster than free-draining Rouse beads in the same solvent.

When should I use the Rouse, Zimm or reptation result?

Use Zimm for dilute solutions, Rouse for unentangled melts and semidilute solutions at short lengths where hydrodynamics is screened, and reptation for entangled melts with N above the entanglement length. The calculator shows all three so you can compare scalings.

How do I get the hydrodynamic radius from D?

Rearrange Stokes-Einstein, Rh = k T / (6 pi eta D). With D = 100 um^2/s in water at 298 K and 1 mPa s the result is Rh = 2.18 nm. Use the Stokes-Einstein mode and select D as the known quantity.

What units does the calculator use for diffusion coefficients?

Results are given in m^2/s and cm^2/s, and the Stokes-Einstein mode also shows um^2/s. One cm^2/s equals 10^-4 m^2/s and one um^2/s equals 10^-12 m^2/s, so 4.365e-11 m^2/s is 4.365e-7 cm^2/s or 43.65 um^2/s.

How is this different from the Einstein-Stokes biophysics calculator?

That page treats a rigid particle of known radius. This one starts from the chain length N and segment length b, builds Rg and Rh for a flexible coil, and adds the Rouse and reptation scalings with their different dependence on N.

What does the Rg/Rh ratio do here?

It converts the chain size into a hydrodynamic radius, Rh = Rg / ratio. For a flexible coil the ratio is about 1.5, a hard sphere gives 0.775. The default 1.5 is an illustrative value, so replace it with a measurement when you have one.