Number-Average and Weight-Average Molecular Weight Calculator
Find the number-average, weight-average and z-average molecular weights and the polydispersity index of a polymer from its fractions.
⚖️ What are Number-Average and Weight-Average Molecular Weights?
A synthetic polymer is never a single molecule. Every sample is a mixture of chains with different lengths, so there is no single molecular weight, only a distribution and a set of averages taken from it. The number-average molecular weight Mn is the ordinary arithmetic mean: the total mass of the sample divided by the number of chains. The weight-average molecular weight Mw weights each chain by its own mass, so heavier chains count for more. A third average, the z-average Mz, weights by mass squared and is driven by the very longest chains. Because short chains are numerous and long chains are heavy, the three always obey Mn ≤ Mw ≤ Mz, with equality only for a perfectly uniform sample.
The ratio Mw/Mn is the polydispersity index, now preferably called the dispersity. It is a single number that describes how broad the distribution is. A value of 1 means every chain is identical. Living anionic polymerization can approach 1.02 to 1.1, free-radical polymerization typically gives values near 2, and step-growth, branched or multi-site systems can be 2 or higher. Different experiments measure different averages: osmometry and end-group analysis give Mn, static light scattering gives Mw, viscometry gives a viscosity-average that sits close to Mw, and gel permeation chromatography can give the full curve from which all of them follow.
Which average matters depends on the property. Colligative properties and the stoichiometry of end groups follow Mn, while mechanical strength, melt viscosity and toughness follow the heavy chains and therefore Mw or Mz. Two samples with the same Mn can behave very differently if one has a long high-mass tail, which is exactly why reporting PDI alongside Mn is standard practice. This is a statistical calculator and is not the formula-mass tool: for the molar mass of a small molecule, use the molecular weight calculator.
This page has two modes. The fractions table takes up to eight fractions, each with an amount and a molar mass, entered either by number or by weight, and returns all three averages and the PDI with a histogram. The PDI mode is a direct Mw/Mn tool that can also solve for Mw or Mn from the other two values, and it includes an interpretation table of typical ranges. For chain length instead of mass see the degree of polymerization calculator, and for a viscosity-based average see the Mark-Houwink calculator.
📐 Formula
Typical dispersity ranges (typical values, not strict limits)
| PDI | Typical meaning |
|---|---|
| 1.0 | Monodisperse, an idealization (some purified proteins come close) |
| about 1.02 to 1.1 | Living anionic polymerization, narrow standards |
| about 1.1 to 1.5 | Controlled radical routes such as ATRP or RAFT, some coordination systems |
| about 2 | Conventional free-radical polymerization, ideal linear step growth (PDI = 1 + p) |
| above 2 | Branched chains, high-conversion step growth with branching, multi-site catalysts |
📖 How to Use This Calculator
Two modes
💡 Example Calculations
Example 1 - A symmetric sample by number
N = 10, 20, 40, 20, 10 chains at M = 10,000, 20,000, 30,000, 40,000, 50,000 g/mol
Example 2 - Three fractions by weight
w = 0.2, 0.5, 0.3 at M = 20,000, 50,000, 100,000 g/mol
Example 3 - PDI from Mw and Mn
Mn = 50,000 g/mol and Mw = 100,000 g/mol
Example 4 - Mw of a narrow living sample
Mn = 25,000 g/mol and PDI = 1.05
❓ Frequently Asked Questions
📚 Sources and Notes
The definitions of dispersity and its reference values follow the Wikipedia article on dispersity and the molar mass distribution article. The dispersity ranges in the table are typical guides compiled for orientation and are flagged as typical, not strict limits. The Schulz-Zimm curve is a standard model shape used for illustration.
See also the polymer physics calculators.
🔗 Related Calculators
How do you calculate number-average molecular weight?
Mn is the total mass divided by the total number of chains: Mn = sum(N_i M_i) / sum(N_i). For 10, 20, 40, 20 and 10 chains of 10,000 to 50,000 g/mol the result is 30,000 g/mol.
How do you calculate weight-average molecular weight?
Mw weights each chain by its mass: Mw = sum(N_i M_i^2) / sum(N_i M_i). For the same sample Mw is 34,000 g/mol. Equivalently Mw = sum(w_i M_i) over weight fractions w_i.
What is the polydispersity index?
The polydispersity index PDI, now called dispersity, is Mw / Mn. It is 1 only when all chains have the same mass and grows as the distribution broadens. Here the example sample has PDI = 34,000 / 30,000 = 1.133.
What is Mz?
Mz is the z-average molar mass, sum(N_i M_i^3) / sum(N_i M_i^2). It weights the heaviest chains even more strongly than Mw and is sensitive to a high-molar-mass tail. For a polydisperse sample Mn < Mw < Mz.
Why is Mw always greater than Mn?
Mw weights long chains more heavily than Mn does, so unless every chain has the same mass, Mw exceeds Mn. They are equal only for a perfectly uniform sample, which makes the dispersity at least 1.
What PDI is typical for different polymerizations?
Typical values are about 1.02 to 1.1 for living anionic polymerization, near 2 for free-radical polymerization and ideal linear step growth, and above 2 for branched or broad systems. These are typical ranges, not strict limits.
How do you find Mn from weight fractions?
Use Mn = 1 / sum(w_i / M_i) with w_i normalized to 1. For weight fractions 0.2, 0.5 and 0.3 at 20,000, 50,000 and 100,000 g/mol, Mn = 43,478 g/mol and Mw = 59,000 g/mol.
What is a good PDI for a polymer?
It depends on the use. Calibration standards and block copolymers for nanostructures want PDI below about 1.1, while commodity plastics are processed happily at 2 or more. A broad distribution can even help melt processing.
What is the standard deviation of a molar mass distribution?
For the number distribution the variance is Mn(Mw - Mn), so the standard deviation is Mn sqrt(PDI - 1). With Mn = 50,000 g/mol and PDI = 2 it is 50,000 g/mol.
Which method measures which average?
Osmometry and end-group analysis give Mn, light scattering gives Mw, viscometry gives Mv close to Mw, and sedimentation can give Mz. Gel permeation chromatography gives the whole distribution when calibrated.