Melting Temperature Depression Calculator (Flory)

Predict how a diluent, a comonomer or a thin lamella lowers the melting point of a semicrystalline polymer below its equilibrium value.

🌡️ Melting Temperature Depression Calculator (Flory)
Polymer preset (illustrative)
Equilibrium melting point (Tm0)
K
Heat of fusion (ΔHu)
kJ/mol
Diluent fraction (φ1)
Repeat unit volume (Vu, illustrative)
cm³/mol
Diluent volume (V1, illustrative)
cm³/mol
Interaction parameter (χ)
Heat of fusion (ΔHu)
kJ/mol
Crystallizable mole fraction (XA)
Fold surface energy (σe, illustrative)
mJ/m²
Lamellar thickness (l)
nm
Heat of fusion (ΔHf)
J/g
Crystal density (ρc)
g/cm³
Melting point (Tm)
—
Tm in °C
—
Depression (Tm0 - Tm)
—
Tm at χ = 0
—
Recovered by χ
—
1/Tm - 1/Tm0
—

Melting point (Tm)
—
Tm in °C
—
Depression (Tm0 - Tm)
—
ln XA
—
Excluded comonomer
—
Initial slope
—

Melting point (Tm)
—
Tm in °C
—
Depression (Tm0 - Tm)
—
Tm / Tm0
—
Heat of fusion per volume
—
Thickness where Tm = 0
—

🌡️ What is Melting Temperature Depression?

A pure, infinitely large and perfect crystal of a polymer melts at its equilibrium melting temperature Tm0. Real samples melt lower. Anything that lowers the chemical potential of the molten state relative to the crystal, or raises the free energy of the crystal, depresses the melting point. Three causes dominate in polymer science. A low molar mass diluent mixed into the melt stabilises the liquid by the entropy and enthalpy of mixing. A comonomer that cannot enter the crystal lattice dilutes the crystallizable sequences in the same way. And a thin lamella with folded surfaces carries a surface free energy penalty that makes small crystals melt early. This calculator handles all three.

For a polymer with a diluent, Flory showed that 1/Tm - 1/Tm0 = (R/ΔHu)(Vu/V1)(φ1 - χ φ12). Here ΔHu is the heat of fusion per repeat unit, Vu and V1 are the molar volumes of the repeat unit and the diluent, φ1 is the diluent volume fraction and χ is the Flory-Huggins interaction parameter. A smaller χ means a better solvent and a larger depression, and fitting this equation to melting data is a classic way to measure χ. For a random copolymer in which the second monomer is fully excluded from the crystal, Flory's 1955 result is 1/Tm - 1/Tm0 = -(R/ΔHu) ln XA, with XA the mole fraction of crystallizable units. Finally, the Gibbs-Thomson relation Tm = Tm0(1 - 2σe/(ΔHv l)) links the melting point to the lamellar thickness l, the fold surface free energy σe and the heat of fusion per crystal volume.

These models make different assumptions, so choose the one that matches your sample. The diluent and copolymer forms give equilibrium values that apply to crystals of effectively infinite thickness, while the Gibbs-Thomson form describes the size effect on its own. In practice they combine, and a real peak sits below all three predictions. Comonomer inclusion in the crystal, polydispersity, chain ends and thickening during heating all shift the result, so the page reports the depression relative to Tm0 rather than claiming an absolute prediction. The presets are rounded illustrative numbers for polyethylene, polypropylene and PET and you should replace them with values cited for your material. To go from enthalpy to crystalline content see the DSC crystallinity calculator, and for χ itself see the Flory-Huggins interaction parameter calculator.

📐 Formula

1/Tm − 1/Tm0  =  (R ÷ ΔHu)(Vu ÷ V1)(φ1 − χ φ12)
Tm = melting temperature of the mixture (K); Tm0 = equilibrium melting temperature of the pure polymer (K)
R = gas constant, 8.314 J/(mol K); ΔHu = heat of fusion per repeat unit (J/mol)
Vu, V1 = molar volumes of the repeat unit and of the diluent (cm3/mol)
φ1 = diluent volume fraction; χ = Flory-Huggins interaction parameter
Example: Tm0 = 414.6 K, ΔHu = 4.11 kJ/mol, Vu/V1 = 16.5/123, φ1 = 0.3, χ = 0.3 gives Tm = 402.24 K
1/Tm − 1/Tm0  =  −(R ÷ ΔHu) ln XA   |   Tm  =  Tm0 (1 − 2σe ÷ (ΔHv l))
XA = mole fraction of crystallizable units, with the comonomer excluded from the crystal (Flory 1955)
σe = fold surface free energy (J/m2); l = lamellar thickness (m)
ΔHv = heat of fusion per volume of crystal = ΔHf (J/g) × ρc (g/cm3) × 106 (J/m3)
Example: XA = 0.95 gives Tm = 397.50 K; l = 10 nm, σe = 90 mJ/m2, ΔHf = 293 J/g, ρc = 1.00 gives Tm = 389.13 K

📖 How to Use This Calculator

Three modes

1
Choose a preset - The illustrative presets fill Tm0 and the heat of fusion, crystal density and surface energy together. Typing a different Tm0 switches the preset to Custom.
2
Diluent mode - Enter the heat of fusion per repeat unit, the two molar volumes, the diluent volume fraction and χ. The calculator also shows Tm at χ = 0 so you can see the effect of the interaction term.
3
Copolymer or Lamella mode - For a copolymer enter the crystallizable mole fraction XA. For a lamella enter the fold surface energy, heat of fusion in J/g, crystal density and thickness.
4
Read Tm and the chart - Read the melting point in kelvin and °C, and check the chart for the shape of the curve. The dashed guide marks your input.

💡 Example Calculations

Example 1 - Polyethylene with 30 percent diluent

Tm0 = 414.6 K, ΔHu = 4.11 kJ/mol, Vu = 16.5, V1 = 123 cm³/mol, φ1 = 0.3, χ = 0.3

1
R/ΔHu = 8.3145 / 4110 = 2.0230 × 10-3 K-1 and Vu/V1 = 0.13415.
2
φ1 - χ φ12 = 0.3 - 0.027 = 0.273, so 1/Tm = 1/414.6 + 2.0230 × 10-3 × 0.13415 × 0.273 = 2.48605 × 10-3.
3
Tm = 402.24 K = 129.09 °C, a depression of 12.36 K.
Tm = 402.24 K (129.09 °C), depression = 12.36 K
Try this example →

Example 2 - The same system in an ideal diluent

Same inputs, χ = 0

1
The interaction term is now the full φ1 = 0.3, so 1/Tm = 1/414.6 + 2.0230 × 10-3 × 0.13415 × 0.3 = 2.49338 × 10-3.
2
Tm = 401.06 K, a depression of 13.54 K, which is 1.18 K more than with χ = 0.3.
Tm = 401.06 K, depression = 13.54 K
Try this example →

Example 3 - Polyethylene with 5 mol percent comonomer

Tm0 = 414.6 K, ΔHu = 4.11 kJ/mol, XA = 0.95

1
ln 0.95 = -0.05129, so 1/Tm = 1/414.6 + 2.0230 × 10-3 × 0.05129 = 2.5157 × 10-3.
2
Tm = 397.50 K = 124.35 °C, a depression of 17.10 K.
3
The small-content slope Tm0² R / ΔHu is 3.477 K per mol percent comonomer.
Tm = 397.50 K (124.35 °C), depression = 17.10 K
Try this example →

Example 4 - A 10 nm polyethylene lamella

Tm0 = 414.6 K, σe = 90 mJ/m², ΔHf = 293 J/g, ρc = 1.00 g/cm³, l = 10 nm

1
ΔHv = 293 × 1.00 = 293.0 J/cm³ = 2.93 × 108 J/m³.
2
2σe/(ΔHv l) = 0.18 / (2.93 × 108 × 10-8) = 0.06143.
3
Tm = 414.6 × (1 - 0.06143) = 389.13 K = 115.98 °C, which is 93.86 percent of Tm0.
Tm = 389.13 K (115.98 °C), depression = 25.47 K
Try this example →

❓ Frequently Asked Questions

What is melting point depression in polymers?+
It is the lowering of the melting temperature of a crystalline polymer by something that is rejected from the crystal, such as a diluent, a comonomer unit or defects, or by the finite thickness of the crystal. The depression is predicted by the Flory theory and by the Gibbs-Thomson equation.
What is the Flory equation for a polymer with a diluent?+
1/Tm - 1/Tm0 = (R/dHu)(Vu/V1)(phi1 - chi phi1^2), where dHu is the heat of fusion per repeat unit, Vu and V1 are the molar volumes of the repeat unit and diluent, phi1 the diluent volume fraction and chi the Flory-Huggins parameter.
How does the interaction parameter chi change the result?+
The term phi1 - chi phi1^2 shrinks as chi grows, so a poor solvent depresses the melting point less than a good one. With the default inputs the melting point is 401.06 K at chi = 0, 402.24 K at chi = 0.3 and 403.04 K at chi = 0.5.
What is the Flory copolymer melting equation?+
For a random copolymer in which comonomer B is excluded from the crystals of A, 1/Tm - 1/Tm0 = -(R/dHu) ln X_A, where X_A is the mole fraction of crystallizable units. Five mole percent of excluded comonomer lowers polyethylene from 414.6 K to 397.5 K.
What is the Gibbs-Thomson equation for polymer crystals?+
Tm = Tm0 (1 - 2 sigma_e / (dHv l)), with sigma_e the fold surface free energy, dHv the heat of fusion per unit volume of crystal and l the lamellar thickness. A plot of Tm against 1/l is linear and its intercept at 1/l = 0 is Tm0.
What is the equilibrium melting temperature Tm0?+
It is the melting temperature of an infinitely large, perfect crystal of the polymer, which cannot be measured directly. It is obtained by extrapolation, for example from Hoffman-Weeks or Gibbs-Thomson plots, and values for one polymer differ by several kelvin between publications.
Why is measured Tm lower than Tm0?+
Real polymer crystals are thin lamellae with folded surfaces of high free energy, and often contain defects. With sigma_e = 90 mJ/m2 a 10 nm polyethylene lamella melts about 25 K below Tm0, which is the typical size of the gap seen in DSC.
Do the Flory equations work for short chains?+
The diluent equation is written for a high molar mass polymer. For short chains and oligomers end groups also lower the melting point, so extra terms appear. Use the results as an upper estimate when the degree of polymerization is small.
How do I find the number of repeat units per volume?+
Divide the repeat unit molar mass by the amorphous density to get Vu in cm3/mol, for example about 16.5 cm3/mol for a CH2 unit in the melt. The default value is illustrative, as is the diluent volume of 123 cm3/mol.
What are the units used by this calculator?+
Temperatures are in kelvin with a degree Celsius conversion, heat of fusion per repeat unit in kJ/mol or per gram in J/g, molar volumes in cm3/mol, surface free energy in mJ/m2, density in g/cm3 and thickness in nm. R is 8.314 J/(mol K).

📚 Sources and Notes

The diluent equation and its interpretation, including the role of χ and the high molar mass limit, are described in the study of polypropylene melting point depression by alkanes. The copolymer form and its assumption that the comonomer is excluded from the crystal are covered in the NIST analysis Crystallization of random copolymers, and the Gibbs-Thomson relation between melting point and lamellar thickness in this paper on the Gibbs-Thomson equation for polymers. The molar volume ratio of 16.5/123, the heat of fusion per repeat unit, the equilibrium melting points and the surface free energies of 90 to 100 mJ/m² in the presets are rounded illustrative values and not confirmed against a cited table, and the fold surface energy for polypropylene and PET in particular is a placeholder. Treat every result as a model estimate.

See also the polymer physics calculators.

What is melting point depression in polymers?

It is the lowering of the melting temperature of a crystalline polymer by something that is rejected from the crystal, such as a diluent, a comonomer unit or defects, or by the finite thickness of the crystal. The depression is predicted by the Flory theory and by the Gibbs-Thomson equation.

What is the Flory equation for a polymer with a diluent?

1/Tm - 1/Tm0 = (R/dHu)(Vu/V1)(phi1 - chi phi1^2), where dHu is the heat of fusion per repeat unit, Vu and V1 are the molar volumes of the repeat unit and diluent, phi1 the diluent volume fraction and chi the Flory-Huggins parameter.

How does the interaction parameter chi change the result?

The term phi1 - chi phi1^2 shrinks as chi grows, so a poor solvent depresses the melting point less than a good one. With the default inputs the melting point is 401.06 K at chi = 0, 402.24 K at chi = 0.3 and 403.04 K at chi = 0.5.

What is the Flory copolymer melting equation?

For a random copolymer in which comonomer B is excluded from the crystals of A, 1/Tm - 1/Tm0 = -(R/dHu) ln X_A, where X_A is the mole fraction of crystallizable units. Five mole percent of excluded comonomer lowers polyethylene from 414.6 K to 397.5 K.

What is the Gibbs-Thomson equation for polymer crystals?

Tm = Tm0 (1 - 2 sigma_e / (dHv l)), with sigma_e the fold surface free energy, dHv the heat of fusion per unit volume of crystal and l the lamellar thickness. A plot of Tm against 1/l is linear and its intercept at 1/l = 0 is Tm0.

What is the equilibrium melting temperature Tm0?

It is the melting temperature of an infinitely large, perfect crystal of the polymer, which cannot be measured directly. It is obtained by extrapolation, for example from Hoffman-Weeks or Gibbs-Thomson plots, and values for one polymer differ by several kelvin between publications.

Why is measured Tm lower than Tm0?

Real polymer crystals are thin lamellae with folded surfaces of high free energy, and often contain defects. With sigma_e = 90 mJ/m2 a 10 nm polyethylene lamella melts about 25 K below Tm0, which is the typical size of the gap seen in DSC.

Do the Flory equations work for short chains?

The diluent equation is written for a high molar mass polymer. For short chains and oligomers end groups also lower the melting point, so extra terms appear. Use the results as an upper estimate when the degree of polymerization is small.

How do I find the number of repeat units per volume?

Divide the repeat unit molar mass by the amorphous density to get Vu in cm3/mol, for example about 16.5 cm3/mol for a CH2 unit in the melt. The default value is illustrative, as is the diluent volume of 123 cm3/mol.

What are the units used by this calculator?

Temperatures are in kelvin with a degree Celsius conversion, heat of fusion per repeat unit in kJ/mol or per gram in J/g, molar volumes in cm3/mol, surface free energy in mJ/m2, density in g/cm3 and thickness in nm. R is 8.314 J/(mol K).