Flory-Huggins Interaction Parameter Calculator

Estimate the Flory-Huggins chi parameter, compare it with the critical value for your chain lengths, and see the free energy of mixing.

⚗️ Flory-Huggins Interaction Parameter Calculator
Component 1 length (N1)
Component 2 length (N2)
Reference volume (V)
cm³/mol
Temperature (T)
K
δ1 (illustrative)
MPa0.5
δ2 (illustrative)
MPa0.5
Entropic constant
Your chi to compare
Volume fraction of 1 (φ)
Chi (χ)
Interaction parameter (χ)
—
Critical χ
—
Enthalpic part
—
Margin (χc minus χ)
—
χ / χc
—
|δ1 minus δ2|
—

Critical χ
—
Critical φ of component 1
—
Long-chain solvent limit
—
Margin (χc minus χ)
—
χ / χc
—
Verdict
—

Free energy of mixing f
—
Ideal mixing (χ = 0)
—
Curvature d²f/dφ²
—
Spinodal χ at this φ
—
Critical χ
—
Local stability
—

⚗️ What is the Flory-Huggins Interaction Parameter?

The Flory-Huggins interaction parameter, chi (χ), is the single number that summarises whether a polymer and a second component want to mix. It comes from the lattice model that Paul Flory and Maurice Huggins developed independently in 1941. The model places every polymer segment and every solvent molecule on a lattice site, counts the ways of arranging them to get the entropy of mixing, and adds an energy term proportional to χ for unlike neighbours. Positive χ means unlike contacts cost energy, so the system tends to separate. Negative χ means unlike contacts are favourable and mixing is easy.

The reason chain length matters so much is entropy. When a long chain mixes it gains far less translational entropy than the same mass of small molecules, because all of its segments are tied together. As a result the critical value χc = 0.5 (1/√N1 + 1/√N2)2 drops as chains get longer. A polymer in a small-molecule solvent needs χ below about 0.5 to dissolve at all concentrations, while two long polymers must have a χ of order 2/N, which is tiny, to blend. That is why most polymer pairs are immiscible and why solvent quality is judged by comparing χ with 0.5.

Chemists estimate χ from solubility parameters, the square root of the cohesive energy density, using χ = Vref (δ1 − δ2)2 / (R T) + 0.34. The first term is the enthalpic contribution, which grows with the difference between the two parameters and falls with temperature. The second is an empirical entropic constant often used for polymer solutions. Typical uses include choosing a solvent for casting a film, screening additives and compatibilisers, predicting whether a blend will be cloudy, and interpreting the cloud point of a solution on heating or cooling.

This calculator offers three views. Chi from solubility turns solubility parameters into χ and compares it with the critical value. Critical chi gives χc and the critical composition for any pair of chain lengths. Free energy evaluates the Flory-Huggins free energy of mixing per lattice site, its curvature and the spinodal. The binodal, which needs a common tangent construction, is not computed. See also the Flory exponent calculator and the Fox equation estimator for blend properties.

📐 Formula

χ  =  Vref (δ1 − δ2)2 ÷ (R T)  +  0.34,    χc  =  ½ (1/√N1 + 1/√N2)2
Vref = reference molar volume (cm³/mol), usually the solvent or a segment volume
δ1, δ2 = solubility parameters (MPa0.5)
R = 8.314 J/(mol K), T = absolute temperature (K)
N1, N2 = degrees of polymerisation (1 for a small-molecule solvent)
Critical composition: φc = √N2 / (√N1 + √N2)
Example: V = 106.3, δ = 18.6 and 18.2, T = 298.15 K gives χ = 0.0069 + 0.34 = 0.3469
f  =  (φ/N1) ln φ  +  ((1 − φ)/N2) ln(1 − φ)  +  χ φ (1 − φ)
f = free energy of mixing per lattice site in units of kT
φ = volume fraction of component 1
Curvature: f″ = 1/(N1 φ) + 1/(N2 (1 − φ)) − 2 χ; the spinodal is where f″ = 0
Example: N1 = N2 = 10, φ = 0.5, χ = 0.3 gives f = 0.0057 kT and f″ = −0.2

📖 How to Use This Calculator

Three modes

1
Choose a mode - Pick Chi from solubility to estimate χ, Critical chi to compare a χ with the critical value, or Free energy to see the mixing free energy at a composition.
2
Enter chain lengths and parameters - Enter the degrees of polymerisation N1 and N2 (use 1 for a solvent), then the solubility parameters, molar volume and temperature, or the χ and composition.
3
Read the verdict and the chart - Compare χ with the critical value, read the free energy and curvature, and use the chart to see where χ crosses the critical line or where the free energy curve becomes non-convex.
4
Adjust the entropic constant - Keep 0.34 for polymer solutions, or set it to 0 when you only want the enthalpic estimate for a polymer blend.

💡 Example Calculations

Example 1 - Polystyrene in toluene (illustrative parameters)

N1 = 1000, N2 = 1, V = 106.3 cm³/mol, δ1 = 18.6, δ2 = 18.2 MPa0.5, T = 298.15 K

1
Enthalpic part = 106.3 × (0.4)2 / (8.3145 × 298.15) = 17.008 / 2478.96 = 0.0069.
2
χ = 0.0069 + 0.34 = 0.3469. The critical value is χc = 0.5 (1/√1000 + 1)2 = 0.5321.
3
χ is 0.1853 below χc (ratio 0.652), so the solution is miscible in all proportions.
χ = 0.3469, χc = 0.5321, miscible
Try this example →

Example 2 - Two polymers of 100 segments each

N1 = N2 = 100, V = 100 cm³/mol, δ1 = 18.6, δ2 = 19.6, T = 298.15 K, constant = 0 (illustrative)

1
χ = 100 × (1.0)2 / (8.3145 × 298.15) = 100 / 2478.96 = 0.0403.
2
χc = 0.5 (0.1 + 0.1)2 = 0.0200, so χ / χc = 2.017.
3
The margin is −0.0203, so the blend is predicted to phase separate despite the small solubility parameter gap.
χ = 0.0403, χc = 0.0200, phase separation
Try this example →

Example 3 - Critical chi for an asymmetric blend

N1 = 1000, N2 = 100, comparing χ = 0.01

1
χc = 0.5 (1/√1000 + 1/√100)2 = 0.5 (0.03162 + 0.1)2 = 0.0087.
2
Critical composition φc = 10 / (31.62 + 10) = 0.2403.
3
χ / χc = 0.01 / 0.00866 = 1.154, so the mixture lies in the two-phase region.
χc = 0.0087, φc = 0.2403, phase separation
Try this example →

Example 4 - Free energy inside the spinodal

N1 = N2 = 10, φ = 0.5, χ = 0.3

1
f = 0.1 ln 0.5 + 0.3 × 0.25 = −0.0693 + 0.075 = 0.0057 kT, while ideal mixing would give −0.0693 kT.
2
Curvature f″ = 0.2 + 0.2 − 0.6 = −0.2000, which is negative.
3
The spinodal χ at this composition and the critical χ are both 0.2000, and χ = 0.3 exceeds them, so the 50:50 mixture is unstable.
f = 0.0057 kT, curvature = −0.2000, unstable
Try this example →

❓ Frequently Asked Questions

What is the Flory-Huggins interaction parameter chi?+
Chi is a dimensionless measure of the energy cost of replacing a contact between like segments by a contact between unlike segments, in units of kT. In Flory-Huggins theory positive chi favours demixing, while the chain lengths set how large chi must be before phase separation occurs.
How do you calculate chi from solubility parameters?+
Use chi = V_ref (delta1 - delta2)^2 / (R T) + 0.34, with V_ref the reference molar volume in cm3/mol, delta in MPa^0.5, R = 8.314 J/(mol K) and T in kelvin. The 0.34 term is an empirical entropic correction for polymer solutions.
What is the critical chi for phase separation?+
chi_c = 0.5 (1/sqrt(N1) + 1/sqrt(N2))^2. For a long polymer in a small-molecule solvent (N1 = 1000, N2 = 1) chi_c = 0.532. For a 100-mer blended with another 100-mer chi_c = 0.020. Above chi_c the mixture separates over a range of compositions.
What is the Flory-Huggins free energy of mixing?+
Per lattice site and in units of kT, f = (phi/N1) ln phi + ((1-phi)/N2) ln(1-phi) + chi phi (1-phi). The first two terms are the combinatorial entropy of mixing and the last term is the interaction energy. A positive second derivative of f means the mixture is locally stable.
What is the critical composition?+
The critical volume fraction of component 1 is phi_c = sqrt(N2) / (sqrt(N1) + sqrt(N2)). It is 0.5 for a symmetric blend with N1 = N2 and shifts toward the shorter component's side: for N1 = 1000 and N2 = 100 it is 0.240.
How do chain lengths affect miscibility?+
The entropy gain from mixing is split among N segments, so long chains gain very little. Doubling both chain lengths roughly halves the critical chi for a blend. This is why two different high molecular weight polymers rarely mix unless they have specific favourable interactions.
What does it mean when chi is negative?+
A negative chi means unlike contacts are energetically favoured, as in blends with hydrogen bonding or other specific attractions. The mixture is then stable at all compositions, and the curvature of the free energy is always positive.
How is the spinodal different from the binodal?+
The spinodal is where the free energy curvature is zero, chi_s = 0.5 (1/(N1 phi) + 1/(N2 (1-phi))). Inside it the mixture is unstable and separates spontaneously. The binodal, from the common tangent construction, marks where two coexisting phases form and lies outside the spinodal. This calculator reports the spinodal, not the binodal.
Why is chi often written as A/T + B?+
Simple theory predicts an interaction energy proportional to 1/T, plus an entropic term B that is roughly temperature independent. The solubility-parameter route gives A = V (delta1 - delta2)^2 / R and B = 0.34, so chi falls as temperature rises.
How accurate is the solubility parameter estimate of chi?+
It is a rough screening tool. It ignores specific interactions, composition dependence of chi and the real volume change on mixing, so measured chi can differ by a factor of two or more. Use it to rank candidate solvents or blend partners rather than to predict exact cloud points.

📚 Sources and Notes

The lattice model and the free energy of mixing follow the Wikipedia article on Flory-Huggins solution theory and the IUPAC Gold Book entry. Using solubility parameters to estimate chi is discussed in the Hansen solubility parameter article. The constant 0.34 is an empirical value and the solubility parameters in the default example are illustrative, so replace them with data for your own materials.

See also the polymer physics calculators.

What is the Flory-Huggins interaction parameter chi?

Chi is a dimensionless measure of the energy cost of replacing a contact between like segments by a contact between unlike segments, in units of kT. In Flory-Huggins theory positive chi favours demixing, while the chain lengths set how large chi must be before phase separation occurs.

How do you calculate chi from solubility parameters?

Use chi = V_ref (delta1 - delta2)^2 / (R T) + 0.34, with V_ref the reference molar volume in cm3/mol, delta in MPa^0.5, R = 8.314 J/(mol K) and T in kelvin. The 0.34 term is an empirical entropic correction for polymer solutions.

What is the critical chi for phase separation?

chi_c = 0.5 (1/sqrt(N1) + 1/sqrt(N2))^2. For a long polymer in a small-molecule solvent (N1 = 1000, N2 = 1) chi_c = 0.532. For a 100-mer blended with another 100-mer chi_c = 0.020. Above chi_c the mixture separates over a range of compositions.

What is the Flory-Huggins free energy of mixing?

Per lattice site and in units of kT, f = (phi/N1) ln phi + ((1-phi)/N2) ln(1-phi) + chi phi (1-phi). The first two terms are the combinatorial entropy of mixing and the last term is the interaction energy. A positive second derivative of f means the mixture is locally stable.

What is the critical composition?

The critical volume fraction of component 1 is phi_c = sqrt(N2) / (sqrt(N1) + sqrt(N2)). It is 0.5 for a symmetric blend with N1 = N2 and shifts toward the shorter component's side: for N1 = 1000 and N2 = 100 it is 0.240.

How do chain lengths affect miscibility?

The entropy gain from mixing is split among N segments, so long chains gain very little. Doubling both chain lengths roughly halves the critical chi for a blend. This is why two different high molecular weight polymers rarely mix unless they have specific favourable interactions.

What does it mean when chi is negative?

A negative chi means unlike contacts are energetically favoured, as in blends with hydrogen bonding or other specific attractions. The mixture is then stable at all compositions, and the curvature of the free energy is always positive.

How is the spinodal different from the binodal?

The spinodal is where the free energy curvature is zero, chi_s = 0.5 (1/(N1 phi) + 1/(N2 (1-phi))). Inside it the mixture is unstable and separates spontaneously. The binodal, from the common tangent construction, marks where two coexisting phases form and lies outside the spinodal. This calculator reports the spinodal, not the binodal.

Why is chi often written as A/T + B?

Simple theory predicts an interaction energy proportional to 1/T, plus an entropic term B that is roughly temperature independent. The solubility-parameter route gives A = V (delta1 - delta2)^2 / R and B = 0.34, so chi falls as temperature rises.

How accurate is the solubility parameter estimate of chi?

It is a rough screening tool. It ignores specific interactions, composition dependence of chi and the real volume change on mixing, so measured chi can differ by a factor of two or more. Use it to rank candidate solvents or blend partners rather than to predict exact cloud points.