Degree of Polymerization Calculator

Calculate the degree of polymerization from molar mass, from conversion with the Carothers equation, or from chain-growth kinetics.

🔗 Degree of Polymerization Calculator
Repeat unit preset (from standard atomic weights)
Polymer molar mass (M)
g/mol
Repeat unit mass (M0)
g/mol
Monomer residues per repeat unit
Length per repeat unit (illustrative, optional)
nm
Conversion (p)
%
Stoichiometric ratio (r)
Target Xn (optional)
Termination mode
Propagation constant kp (illustrative)
L/(mol s)
Monomer concentration [M]
mol/L
Initiator decomposition kd (illustrative)
1/s
Initiator efficiency (f)
Initiator concentration [I]
mol/L
Termination constant kt (illustrative)
L/(mol s)
Degree of polymerization (DP)
—
Monomer residues
—
Repeat unit mass
—
Polymer molar mass
—
Contour length (nm)
—
Contour length (µm)
—

Number-average Xn
—
Maximum Xn at p = 1
—
Conversion for target Xn
—
Weight-average Xw (r = 1)
—
Dispersity (r = 1)
—
Unreacted groups
—

Kinetic chain length (ν)
—
Number-average Xn
—
Polymerization rate Rp
—
Initiation rate Ri
—
Xn per kinetic chain
—
Initiator half-life
—

🔗 What is the Degree of Polymerization?

The degree of polymerization, usually written DP or X, is the number of repeat units in a polymer chain. It is the most direct measure of how long a macromolecule is, and it links the molecular mass of a polymer to the chemistry of its building block. A polyethylene chain with 5000 repeat units has a degree of polymerization of 5000 and a molar mass of about 140,000 g/mol, because each ethylene repeat unit weighs about 28.05 g/mol. Since a real sample contains chains of many different lengths, DP is reported as an average: the number-average DPn, the weight-average DPw, or less often the viscosity-average.

The same quantity is controlled by very different chemistry depending on how the polymer is made. In step-growth polymerization, such as the formation of polyesters and nylons, any two reactive species can join, so long chains appear only when nearly every functional group has reacted. The Carothers equation, Xn = 1 / (1 - p), captures this and shows why a conversion of 99 percent is needed just to reach Xn = 100. In chain-growth polymerization, such as free-radical polymerization of vinyl monomers, long chains form quickly from the start, and the chain length is set by the kinetic chain length, the number of monomers added per initiating radical, which depends on the monomer and initiator concentrations and on the rate constants.

Several practical points matter. Stoichiometry is critical in step growth: a small excess of one monomer caps the achievable chain length no matter how long you wait. The repeat unit is not always the monomer, because condensation polymers lose a small molecule and often contain two monomer residues per repeat unit, so this calculator lets you set the number of residues per repeat unit. The contour length DP times l is only the fully extended length; a real flexible chain adopts a coil whose size grows only with the square root of DP, as the chain end-to-end distance calculator shows.

Use this tool to convert between molar mass and chain length, to plan the conversion and stoichiometry needed for a target chain length, and to estimate the kinetic chain length of a radical polymerization. To move from a single molar mass to the full distribution, see the number-average and weight-average molecular weight calculator, and for a molar mass from solution viscosity see the Mark-Houwink calculator.

📐 Formula

DP  =  Mpolymer ÷ M0
DP = number of repeat units (DPn when M is a number average)
Mpolymer = polymer molar mass (g/mol)
M0 = repeat unit mass (g/mol), for example 28.05 for ethylene
Contour length: L = DP × l, with l the extended length per repeat unit (about 0.25 nm for a vinyl backbone, illustrative)
Example: M = 140,250 g/mol and M0 = 28.05 g/mol give DP = 5000
Xn  =  (1 + r) ÷ (1 + r − 2 r p)  →  1 ÷ (1 − p) for r = 1
p = fractional conversion of the limiting functional groups
r = stoichiometric ratio of reactive groups, at most 1
Limit: Xn,max = (1 + r) / (1 − r) at p = 1
Needed conversion: p = (1 + r)(1 − 1/Xn) / (2 r)
Weight average (r = 1): Xw = (1 + p) / (1 − p), dispersity 1 + p
ν  =  kp [M] ÷ (2 √(f kd kt [I]))
kp, kd, kt = propagation, initiator decomposition and termination rate constants
f = initiator efficiency; [M], [I] = monomer and initiator concentrations (mol/L)
Xn = 2ν for termination by combination, Xn = ν for disproportionation (no chain transfer)
Rates: Ri = 2 f kd [I] and Rp = kp [M] √(Ri / 2 kt)

📖 How to Use This Calculator

Three modes

1
Choose a mode - Pick Molar mass for DP = M / M0, Step growth for the Carothers equation, or Chain growth for the kinetic chain length of a free-radical system.
2
Enter the inputs - Give the polymer molar mass and repeat unit mass (the preset fills the mass), or the conversion and stoichiometric ratio, or the rate constants and concentrations.
3
Read the result and chart - Read DP or Xn with the related quantities, then check the chart for how it changes with mass, conversion or initiator concentration. The dashed guide marks your input.
4
Plan a target - In step growth, type a target Xn to see the conversion needed, or learn that the stoichiometric imbalance makes it unreachable.

💡 Example Calculations

Example 1 - Polyethylene of 140,250 g/mol

M = 140,250 g/mol, ethylene repeat unit 28.05 g/mol, 0.25 nm per unit (illustrative)

1
DP = 140,250 / 28.05 = 5000 repeat units.
2
One monomer per repeat unit, so there are 5000 monomer residues.
3
Contour length = 5000 × 0.25 nm = 1250 nm = 1.25 µm.
DP = 5000, extended length = 1250 nm
Try this example →

Example 2 - A PET chain with two residues per repeat unit

M = 19,217 g/mol, ethylene terephthalate repeat unit 192.17 g/mol

1
DP = 19,217 / 192.17 = 100 repeat units.
2
Each repeat unit contains a terephthalate and a glycol residue, so the number of monomer residues is 100 × 2 = 200.
DP = 100, monomer residues = 200
Try this example →

Example 3 - Carothers equation at 99 percent conversion

Balanced step growth, p = 99 percent, r = 1, target Xn = 100

1
Xn = 1 / (1 - 0.99) = 100.
2
Xw = (1 + 0.99) / (1 - 0.99) = 199, so the dispersity is 1 + p = 1.99.
3
The conversion needed for Xn = 100 is p = 1 × (1 - 1/100) = 99 percent, as expected.
Xn = 100, Xw = 199, dispersity = 1.99
Try this example →

Example 4 - Stoichiometric imbalance caps the chain length

p = 99.5 percent, r = 0.98, target Xn = 100

1
Xn = 1.98 / (1.98 - 2 × 0.98 × 0.995) = 1.98 / 0.0298 = 66.44.
2
The ceiling at full conversion is (1 + 0.98) / (1 - 0.98) = 99.
3
A target of 100 lies above that ceiling, so it is not reachable with this imbalance.
Xn = 66.44, maximum Xn = 99, target not reachable
Try this example →

Example 5 - Free-radical chain growth with illustrative constants

kp = 340, [M] = 4 mol/L, kd = 8.5e-6 1/s, f = 0.6, [I] = 0.01 mol/L, kt = 6e7, combination

1
f kd kt [I] = 0.6 × 8.5e-6 × 6e7 × 0.01 = 3.06, whose square root is 1.749.
2
ν = 340 × 4 / (2 × 1.749) = 388.7 monomers per radical.
3
With combination, Xn = 2 ν = 777.5. The rates are Ri = 1.020e-7 and Rp = 3.965e-5 mol/(L s).
ν = 388.7, Xn = 777.5
Try this example →

❓ Frequently Asked Questions

What is the degree of polymerization?+
The degree of polymerization DP is the number of repeat units in a polymer chain. It equals the polymer molar mass divided by the repeat unit mass, DP = M / M0. For a sample it is reported as a number average DPn or a weight average DPw.
How do you calculate the degree of polymerization from molecular weight?+
Divide the polymer molar mass by the repeat unit mass. Polyethylene with M = 140,250 g/mol and a repeat unit of 28.05 g/mol gives DP = 140,250 / 28.05 = 5000 repeat units.
What is the Carothers equation?+
For step-growth polymerization, Xn = 1 / (1 - p) for balanced reactants, where p is the fraction of functional groups reacted. With a stoichiometric ratio r the form is Xn = (1 + r) / (1 + r - 2 r p). At p = 0.99 and r = 1 the result is Xn = 100.
Why does step-growth polymerization need such high conversion?+
Because chains grow by joining oligomers, long chains only appear when almost every group has reacted. Xn is 10 at 90 percent conversion, 100 at 99 percent and 1000 at 99.9 percent, so small remaining fractions control the final chain length.
How does stoichiometric imbalance limit chain length?+
With r below 1, Xn cannot exceed (1 + r) / (1 - r) even at full conversion. For r = 0.98 the ceiling is 99, and for r = 0.99 it is 199. This is why monomer purity and exact weighing are critical in step growth.
What is the kinetic chain length?+
In free-radical chain growth, the kinetic chain length nu is the average number of monomers added per radical formed. It equals kp[M] / (2 (f kd kt [I])^0.5), the propagation rate divided by the initiation rate.
How does termination change the degree of polymerization?+
If radicals terminate by combination, two growing chains join and Xn = 2 nu. If they terminate by disproportionation, each radical gives one dead chain and Xn = nu. Chain transfer lowers Xn further and is not included here.
How does initiator concentration affect chain length?+
Xn is proportional to [I] to the power -1/2 because faster initiation produces more chains. Quadrupling the initiator concentration halves Xn, while the polymerization rate Rp doubles.
What is the difference between DP and the number of monomers?+
For addition polymers the repeat unit equals one monomer, so the two match. For a condensation polymer such as PET or nylon 6,6 the repeat unit contains two monomer residues, so the number of monomers is twice the DP counted in repeat units.
How long is a polymer chain of a given DP?+
The fully extended contour length is DP times the length per repeat unit, about 0.25 nm for a vinyl backbone in the all-trans form. A chain with DP = 5000 would stretch to roughly 1250 nm, but in solution or melt it is coiled and much shorter.

📚 Sources and Notes

The definition of DP and the worked example of p = 0.99 giving Xn = 100 follow the Wikipedia article on the degree of polymerization and the Carothers equation article. The stoichiometric imbalance form is discussed in the Penn State materials course notes. Repeat unit masses are computed from conventional standard atomic weights. The rate constants, initiator efficiency and the 0.25 nm length per repeat unit are illustrative defaults, not measured data; replace them with values for your system.

See also the polymer physics calculators and the molecular weight calculator.

What is the degree of polymerization?

The degree of polymerization DP is the number of repeat units in a polymer chain. It equals the polymer molar mass divided by the repeat unit mass, DP = M / M0. For a sample it is reported as a number average DPn or a weight average DPw.

How do you calculate the degree of polymerization from molecular weight?

Divide the polymer molar mass by the repeat unit mass. Polyethylene with M = 140,250 g/mol and a repeat unit of 28.05 g/mol gives DP = 140,250 / 28.05 = 5000 repeat units.

What is the Carothers equation?

For step-growth polymerization, Xn = 1 / (1 - p) for balanced reactants, where p is the fraction of functional groups reacted. With a stoichiometric ratio r the form is Xn = (1 + r) / (1 + r - 2 r p). At p = 0.99 and r = 1 the result is Xn = 100.

Why does step-growth polymerization need such high conversion?

Because chains grow by joining oligomers, long chains only appear when almost every group has reacted. Xn is 10 at 90 percent conversion, 100 at 99 percent and 1000 at 99.9 percent, so small remaining fractions control the final chain length.

How does stoichiometric imbalance limit chain length?

With r below 1, Xn cannot exceed (1 + r) / (1 - r) even at full conversion. For r = 0.98 the ceiling is 99, and for r = 0.99 it is 199. This is why monomer purity and exact weighing are critical in step growth.

What is the kinetic chain length?

In free-radical chain growth, the kinetic chain length nu is the average number of monomers added per radical formed. It equals kp[M] / (2 (f kd kt [I])^0.5), the propagation rate divided by the initiation rate.

How does termination change the degree of polymerization?

If radicals terminate by combination, two growing chains join and Xn = 2 nu. If they terminate by disproportionation, each radical gives one dead chain and Xn = nu. Chain transfer lowers Xn further and is not included here.

How does initiator concentration affect chain length?

Xn is proportional to [I] to the power -1/2 because faster initiation produces more chains. Quadrupling the initiator concentration halves Xn, while the polymerization rate Rp doubles.

What is the difference between DP and the number of monomers?

For addition polymers the repeat unit equals one monomer, so the two match. For a condensation polymer such as PET or nylon 6,6 the repeat unit contains two monomer residues, so the number of monomers is twice the DP counted in repeat units.

How long is a polymer chain of a given DP?

The fully extended contour length is DP times the length per repeat unit, about 0.25 nm for a vinyl backbone in the all-trans form. A chain with DP = 5000 would stretch to roughly 1250 nm, but in solution or melt it is coiled and much shorter.