Transmission Calculator

Enter your gearbox ratios, final drive and tyre size to see the speed and rpm in every gear, the shift drop and the gearing top speed.

🕹️ Transmission Calculator
Gear ratios (leave unused gears blank; illustrative defaults)
1st
2nd
3rd
4th
5th
6th
Final drive ratio
Redline
rpm
Tyre width
mm
Aspect ratio
%
Rim diameter
in
Speed unit (chart and speed input)
Engine speed for the table
rpm
5008000
Road speed (in the unit selected above)
10300
Shift at
rpm
10009000
Top gear at redline
—
Top gear at redline (mph)
—
Top gear overall ratio
—
First gear overall ratio
—
Ratio span (first / top)
—
Tyre diameter
—
Tyre circumference
—
Table engine speed
—

Engine rpm in top gear
—
Engine rpm in first gear
—
Road speed
—
Road speed (m/s)
—
Top gear share of redline
—
Tyre diameter
—
Tyre circumference
—

rpm drop, 1st to 2nd
—
rpm after 1st to 2nd
—
Largest drop
—
Speed at the 1st to 2nd shift
—
Top gear at redline
—
Top gear at redline (mph)
—
Shift point
—
Tyre diameter
—
Tyre circumference
—

🕹️ What is a Transmission Calculator?

A transmission calculator turns the gear ratios of a gearbox into numbers you can feel on the road: how fast the car travels in each gear at a given engine speed, how many revolutions per minute the engine makes at a given road speed, and how far the engine speed falls when you change up. It combines three pieces of data. The gearbox ratios say how many times the engine turns for one turn of the gearbox output. The final drive ratio, in the differential, adds a further reduction. The tyre size sets how far the car moves for each turn of the wheel.

The tool is useful for many tasks. Tuners and racers compare gear sets to keep the engine in its power band after each shift. Owners considering a different final drive or larger wheels can see the effect on cruising rpm and fuel use. Engineering students check homework on gear trains. Drivers of vintage and project cars check whether a swap of gearbox will give a sensible top speed. Motorcycle riders and cyclists can use the same maths by treating the chain reduction as the final drive and the wheel circumference as the tyre.

It is worth separating this page from its neighbours. The crawl ratio calculator multiplies the lowest gears of an off-road vehicle with a transfer case, and the gear ratio calculator works from tooth counts of gear pairs. The speedometer gear calculator focuses on the error a tyre or gearing change puts into the speedometer. This page begins with the ratios you already have on a spec sheet and gives a complete road gearing picture: a table for every gear, rpm at a chosen speed and the shift drop.

Keep the limits in mind. The calculation is pure kinematics. It does not include clutch or torque converter slip, the difference between the nominal and the loaded rolling radius of the tyre, power, drag or traction. The top speed shown for each gear is the speed at which the engine reaches the redline, which is a gearing limit and not a prediction of what the car can actually reach. The default gear ratios are illustrative values for a typical six speed gearbox and should be replaced with the figures for your own vehicle.

📐 Formula

v  =  ( n / 60 ) × ( π D ) / ( Rgear × Rfinal )
v = road speed (m/s); multiply by 3.6 for km/h or by 2.2369 for mph
n = engine speed (rpm)
D = tyre diameter (m) = ( rim × 25.4 + 2 × width × aspect / 100 ) / 1000, with width in mm, aspect in percent and rim in inches
Rgear = gearbox ratio of the selected gear, Rfinal = final drive ratio; their product is the overall ratio
Engine rpm at a speed: n = 60 v Rgear Rfinal / ( π D )
rpm after an upshift: nafter = nshift × Rnew / Rold, and the step is Rold / Rnew
Example: 3000 rpm in 6th (0.84 × 3.55 = 2.982) on a 225/45 R17 tyre (1.993 m) gives 120.3 km/h

📖 How to Use This Calculator

Steps

1
Enter the gears and tyres. Type the gearbox ratio for each gear (leave a gear blank if the box has fewer than six), then the final drive ratio, the redline and the tyre width, aspect ratio and rim diameter.
2
Choose a mode. Gear table lists the speed in every gear at an engine speed. RPM at speed gives the engine speed in every gear at a road speed. Shift drop shows the rpm after each upshift at your shift point.
3
Read the table and chart. Use the table for exact numbers, and the chart to see where each gear reaches the redline. In RPM at speed mode, a green line marks your road speed.

💡 Example Calculations

Example 1 — Speeds in Every Gear of a Six Speed Box

Ratios 3.82, 2.20, 1.52, 1.22, 1.02, 0.84 (illustrative), final drive 3.55, 225/45 R17 tyres, redline 6500 rpm, table at 3000 rpm

1
Tyre diameter = 17 × 25.4 + 2 × 225 × 0.45 = 634.3 mm, circumference = 1.993 m
2
Top gear overall = 0.84 × 3.55 = 2.982; first gear overall = 3.82 × 3.55 = 13.561; span = 3.82 / 0.84 = 4.55 : 1
3
At 3000 rpm: 1st = 26.4 km/h, 3rd = 66.5 km/h, 6th = 120.3 km/h. At the 6500 rpm redline in 6th the gearing allows 260.6 km/h (161.9 mph), which is a gearing limit only.
Top gear at redline = 260.6 km/h (161.9 mph), overall ratio 2.982 : 1
Try this example →

Example 2 — A Five Speed Hatchback

Ratios 3.545, 1.955, 1.286, 0.926, 0.756 (illustrative), final drive 4.07, 195/65 R15 tyres, redline 6000 rpm, table at 3000 rpm

1
Tyre diameter = 15 × 25.4 + 2 × 195 × 0.65 = 634.5 mm, circumference = 1.993 m
2
Top gear overall = 0.756 × 4.07 = 3.077; span = 3.545 / 0.756 = 4.69 : 1
3
At 3000 rpm in 5th the car travels 116.6 km/h. At the 6000 rpm redline in 5th the gearing allows 233.2 km/h (144.9 mph).
5th gear at 3000 rpm = 116.6 km/h, at redline = 233.2 km/h
Try this example →

Example 3 — Engine Speed at 100 km/h

The Example 1 car travelling at 100 km/h

1
Speed = 100 / 3.6 = 27.78 m/s
2
6th: n = 60 × 27.78 × 2.982 / 1.993 = 2494 rpm (38 % of redline)
3
3rd gives 4513 rpm. 2nd would need 6532 rpm and 1st 11342 rpm, so both are over the 6500 rpm redline at this speed.
Engine speed in 6th = 2494 rpm, in 1st = 11342 rpm (over redline)
Try this example →

Example 4 — Highway Cruise at 70 mph

The Example 2 hatchback at 70 mph

1
Speed = 70 × 0.44704 = 31.29 m/s
2
5th: n = 60 × 31.29 × 3.077 / 1.993 = 2898 rpm (48 % of the 6000 rpm redline)
3
4th gives 3550 rpm, so dropping a gear for overtaking raises the engine speed by 652 rpm. First and second gear are over the redline at 70 mph.
Engine speed in 5th gear = 2898 rpm
Try this example →

Example 5 — Shift Drop at 6000 rpm

The Example 1 car shifting up at 6000 rpm

1
1st to 2nd step = 3.82 / 2.20 = 1.736, so rpm after = 6000 × 7.810 / 13.561 = 3455 rpm
2
The drop is 6000 − 3455 = 2545 rpm, at a road speed of 52.9 km/h. The later shifts drop 1855, 1184, 984 and 1059 rpm.
3
The first shift is the largest drop because the step is the widest. The 4th to 5th step of 1.196 gives the smallest drop.
rpm after 1st to 2nd = 3455 rpm, drop = 2545 rpm
Try this example →

❓ Frequently Asked Questions

How do you calculate speed from rpm and gear ratio?+
Road speed equals engine rpm divided by 60, times the tyre circumference, divided by the overall ratio, which is the gear ratio times the final drive. With 3000 rpm in sixth (0.84 x 3.55) on a 1.993 m tyre, that is 120.3 km/h.
How do you calculate engine rpm at a given speed?+
Engine rpm equals road speed times the overall ratio times 60, divided by the tyre circumference. At 100 km/h (27.78 m/s) with an overall ratio of 2.982 and a 1.993 m circumference, the engine turns about 2494 rpm.
What is the overall gear ratio?+
The overall ratio is the ratio of engine speed to driven wheel speed in a given gear. It is the transmission gear ratio multiplied by the final drive ratio (and by any transfer case ratio, which this page does not include). A higher number gives more torque at the wheels and lower speed.
How do I find the tyre diameter from the size code?+
For a tyre marked width/aspect R rim, the diameter in millimetres is rim x 25.4 + 2 x width x aspect / 100. A 225/45 R17 tyre is 17 x 25.4 + 2 x 225 x 0.45 = 634.3 mm, giving a circumference of 1.993 m.
How much does the rpm drop when I shift gears?+
The rpm after an upshift equals the shift rpm times the new overall ratio divided by the old one, which is the same as dividing by the step between the two gears. Shifting 1 to 2 at 6000 rpm with a step of 1.736 gives 3455 rpm, a drop of 2545 rpm.
What is the step between gears?+
The step is the lower gear ratio divided by the next higher gear ratio, for example 3.82 / 2.20 = 1.736. Closer steps keep rpm higher after each shift. Many road gearboxes have steps that shrink toward the top gears, as the table in the calculator shows.
Is the gearing top speed the real top speed?+
No. It is the speed at which the engine reaches its redline in that gear, from gearing alone. Real top speed is set by the balance between engine power and aerodynamic drag plus rolling resistance, and is usually reached below the redline in the top gear.
How does tyre size change speed and rpm?+
Speed at a given rpm is proportional to the tyre diameter. A tyre 3 percent taller makes the car travel 3 percent faster at the same rpm, so the speedometer under-reads. The speedometer gear calculator and tire size calculator on this site cover that effect in detail.
How is this different from the crawl ratio and gear ratio calculators?+
The crawl ratio calculator multiplies low range gearing for off-road use, and the gear ratio calculator works from tooth counts. This page starts from the gear ratios you already know and gives speeds, rpm and shift drops in every gear of a road transmission.
Can I use this for a motorcycle or bicycle?+
Yes for any wheeled drivetrain with fixed ratios. For a motorcycle enter the box ratios and use the primary and final drive product as the final drive. For a bicycle, treat chainring over sprocket as the ratio, and the wheel circumference as the tyre size equivalent.

How do you calculate speed from rpm and gear ratio?

Road speed equals engine rpm divided by 60, times the tyre circumference, divided by the overall ratio, which is the gear ratio times the final drive. With 3000 rpm in sixth (0.84 x 3.55) on a 1.993 m tyre, that is 120.3 km/h.

How do you calculate engine rpm at a given speed?

Engine rpm equals road speed times the overall ratio times 60, divided by the tyre circumference. At 100 km/h (27.78 m/s) with an overall ratio of 2.982 and a 1.993 m circumference, the engine turns about 2494 rpm.

What is the overall gear ratio?

The overall ratio is the ratio of engine speed to driven wheel speed in a given gear. It is the transmission gear ratio multiplied by the final drive ratio (and by any transfer case ratio, which this page does not include). A higher number gives more torque at the wheels and lower speed.

How do I find the tyre diameter from the size code?

For a tyre marked width/aspect R rim, the diameter in millimetres is rim x 25.4 + 2 x width x aspect / 100. A 225/45 R17 tyre is 17 x 25.4 + 2 x 225 x 0.45 = 634.3 mm, giving a circumference of 1.993 m.

How much does the rpm drop when I shift gears?

The rpm after an upshift equals the shift rpm times the new overall ratio divided by the old one, which is the same as dividing by the step between the two gears. Shifting 1 to 2 at 6000 rpm with a step of 1.736 gives 3455 rpm, a drop of 2545 rpm.

What is the step between gears?

The step is the lower gear ratio divided by the next higher gear ratio, for example 3.82 / 2.20 = 1.736. Closer steps keep rpm higher after each shift. Many road gearboxes have steps that shrink toward the top gears, as the table in the calculator shows.

Is the gearing top speed the real top speed?

No. It is the speed at which the engine reaches its redline in that gear, from gearing alone. Real top speed is set by the balance between engine power and aerodynamic drag plus rolling resistance, and is usually reached below the redline in the top gear.

How does tyre size change speed and rpm?

Speed at a given rpm is proportional to the tyre diameter. A tyre 3 percent taller makes the car travel 3 percent faster at the same rpm, so the speedometer under-reads. The speedometer gear calculator and tire size calculator on this site cover that effect in detail.

How is this different from the crawl ratio and gear ratio calculators?

The crawl ratio calculator multiplies low range gearing for off-road use, and the gear ratio calculator works from tooth counts. This page starts from the gear ratios you already know and gives speeds, rpm and shift drops in every gear of a road transmission.

Can I use this for a motorcycle or bicycle?

Yes for any wheeled drivetrain with fixed ratios. For a motorcycle enter the box ratios and use the primary and final drive product as the final drive. For a bicycle, treat chainring over sprocket as the ratio, and the wheel circumference as the tyre size equivalent.