Shear Strain Calculator

Find engineering and tensor shear strain from a displacement, an angle, a twisted shaft or a strain gauge rosette, and the shear stress that goes with it.

📐 Shear Strain Calculator
Material (illustrative G)
Shear modulus (G)
GPa
Sideways displacement (dx)
mm
01
Height (h)
mm
Shear angle (θ)
°
045
Outer radius (r)
mm
Length (L)
mm
Angle of twist (θ)
°
010
Gauge at 0° (e0)
µε
Gauge at 45° (e45)
µε
Gauge at 90° (e90)
µε
Shear strain γ
—
Shear strain (%)
—
Shear angle
—
Tensor strain γ/2
—
Shear stress τ = Gγ
—
Shear strain (microradians)
—
Small-angle error
—
G used
—

Sketch of the sheared element (dashed outline is the original). Small shear angles are exaggerated so that the skew is visible.

Shear strain γ = tan θ
—
Angle in radians
—
Small-angle estimate
—
Small-angle error
—
Tensor strain γ/2
—
Shear stress τ = Gγ
—
Shear strain (%)
—
G used
—

Sketch of the sheared element (dashed outline is the original). Small shear angles are exaggerated so that the skew is visible.

Surface shear strain
—
Strain at half radius
—
Surface strain (%)
—
Tensor strain γ/2
—
Surface shear stress
—
Torque T = GJθ/L
—
Twist in radians
—
Twist per length
—

Shear strain γxy
—
Tensor strain γxy/2
—
Principal strain 1
—
Principal strain 2
—
Max in-plane shear strain
—
Principal direction
—
Average normal strain
—
Shear stress τxy
—

📐 What is Shear Strain?

Shear strain measures how much a material is distorted by forces that slide one layer past another instead of pulling or pushing along an axis. Picture a deck of cards pushed sideways, or a rubber block glued between two plates that are moved in opposite directions. The top face moves a distance dx relative to the bottom face, which is a height h away. The engineering shear strain is gamma = dx / h, which is the tangent of the angle through which the vertical edge rotates. It has no units.

Shear strain appears in many practical settings. Torsion of shafts and bolts, rubber bearings and vibration mounts, adhesive joints, soil and rock layers sliding under load, beams under transverse force and the deformation of fluids in flow all involve it. Engineers connect it to stress through the shear modulus, tau = G gamma, so once the strain is known, the shear stress in the elastic range follows immediately. Experimentalists often infer it from strain gauges, because a gauge reads only normal strain, and three gauges at 0, 45 and 90 degrees give enough information to recover the shear strain.

The most common confusion is between engineering and tensor shear strain. Engineering strain gamma is the total change in a right angle. Tensor strain epsilon_xy is half of that, because the strain tensor shares the distortion symmetrically between the two shear components. Stress formulas such as tau = G gamma use the engineering value. A second distinction is between the tangent and the angle itself: gamma = tan(theta) is exact, while gamma = theta in radians is the small-angle approximation. The calculator shows both so you can see when the shortcut starts to fail. Finally, the connection to stress holds only in the elastic range, and the sheared rubber, soil or metal may behave non-linearly at large strains.

The four modes cover the usual starting points. From displacement uses dx and h. From angle starts with a measured shear angle. Torsion shaft uses the radius, length and twist of a round shaft, giving the strain on the surface, half-way in and the torque. Strain rosette takes three gauge readings and returns the shear strain, principal strains and maximum shear strain. The material presets provide illustrative shear moduli and are not design values.

📐 Formula

γ  =  dx / h  =  tan θ,   εxy = γ / 2,   τ = G γ
γ = engineering shear strain (dimensionless); εxy = tensor shear strain
dx = sideways displacement of the top face, h = height between the faces, θ = shear angle
G = shear modulus (GPa); τ = shear stress (MPa), valid in the elastic range
Torsion shaft: γ = r θ / L at radius r, with θ in radians and L the length; torque T = G J θ / L with J = π r⁴ / 2 for a solid shaft
Rosette (0/45/90): γxy = 2 ε45 − ε0 − ε90; principal strains = average ± R with R = √( ((ε0 − ε90) / 2)² + (γxy / 2)² )
Example: dx = 0.05 mm over h = 50 mm gives γ = 0.001; with G = 79 GPa, τ = 79 MPa

📖 How to Use This Calculator

Steps

1
Pick the way you know the shear. Choose From displacement, From angle, Torsion shaft or Strain rosette depending on what you measured.
2
Enter the geometry and the shear modulus. Type the displacement and height, the angle, the shaft dimensions or the three gauge readings. Choose a material preset to fill G, or type your own value in GPa.
3
Read the strains, stress and chart. The main box shows the engineering shear strain. Below it are the tensor strain, the shear stress and the extra outputs for your mode, together with a chart and, for the first two modes, a sketch of the sheared element.

💡 Example Calculations

Example 1 — Steel Block Sheared by 0.05 mm

dx = 0.05 mm over h = 50 mm, steel with G = 79 GPa

1
γ = 0.05 / 50 = 0.001000, which is 0.1000 % or 1000 microradians
2
The shear angle is arctan(0.001) = 0.05730 degrees, and the tensor strain is 0.0005000
3
τ = 79 GPa × 0.001 = 79.00 MPa. The G value is an illustrative textbook figure.
Shear strain = 0.001000, shear stress = 79.00 MPa
Try this example →

Example 2 — Rubber Pad Sheared by 15 Degrees

Shear angle 15°, soft rubber with G = 0.0005 GPa (0.5 MPa)

1
γ = tan(15°) = 0.26795, which is 26.79 %
2
The small-angle estimate is 15° = 0.26180 rad, which is 2.295 % too low
3
τ = 0.5 MPa × 0.26795 = 0.1340 MPa, and the tensor strain is 0.1340. Real rubber is non-linear at this strain, so treat the stress as a rough estimate.
Shear strain = 0.26795, shear stress = 0.1340 MPa
Try this example →

Example 3 — Twisted Steel Shaft

Radius 10 mm, length 500 mm, twist 1.5°, G = 79 GPa

1
θ = 1.5° = 0.02618 rad, so γ = r θ / L = 10 × 0.02618 / 500 = 0.0005236 on the surface
2
Half-way in, the strain is half of that: 0.0002618. The surface shear stress is 79 GPa × 0.0005236 = 41.36 MPa.
3
J = π × 10⁴ / 2 = 15708 mm⁴, so T = G J θ / L = 64.97 N·m
Surface shear strain = 0.0005236, torque = 64.97 N·m
Try this example →

Example 4 — Rectangular Strain Rosette

e0 = 600, e45 = 500, e90 = -200 microstrain, steel with G = 79 GPa

1
γxy = 2 × 500 − 600 − (−200) = 600 µε, and the tensor strain is 300 µε
2
Average strain = 200, R = √(400² + 300²) = 500, so the principal strains are 700 and −300 µε
3
Maximum in-plane shear strain = 2R = 1000 µε, the principal direction is 18.43°, and τxy = 79 GPa × 600 µε = 47.40 MPa
Shear strain = 600 µε, shear stress = 47.40 MPa
Try this example →

❓ Frequently Asked Questions

What is the formula for shear strain?+
Engineering shear strain is gamma = dx / h, the sideways displacement of one face divided by the perpendicular distance between faces, which equals the tangent of the shear angle. For dx = 0.05 mm over h = 50 mm, gamma = 0.001. Shear strain has no units.
What is the difference between engineering and tensor shear strain?+
Engineering shear strain gamma is the total change in a right angle. Tensor shear strain epsilon_xy is half of it, gamma / 2, the symmetric off-diagonal term of the strain tensor. Stress relations such as tau = G gamma use the engineering value.
How do you calculate shear stress from shear strain?+
In the elastic range, shear stress is tau = G gamma. With G = 79 GPa for steel and gamma = 0.001, tau = 79 MPa. The relation holds only up to the elastic limit, and soft materials such as rubber leave the linear range at large strains.
What is the shear strain in a twisted shaft?+
On the surface of a round shaft, gamma = r theta / L, with r the radius, theta the twist in radians and L the length. It falls linearly to zero on the axis. A shaft with r = 10 mm and L = 500 mm twisted 1.5 degrees has a surface strain of 0.0005236.
Is shear strain measured in radians or degrees?+
It is a dimensionless ratio equal to the tangent of the angle. For small angles the tangent is nearly the angle in radians, so shear strain is often quoted in radians even if the angle itself is measured in degrees. It is also written in percent or microstrain.
How do you find shear strain from a strain gauge rosette?+
For a 0/45/90 degree rectangular rosette, gamma_xy = 2 e45 - e0 - e90. Readings of 600, 500 and -200 microstrain give 600 microstrain. The principal strains and maximum shear strain come from the same three readings through the strain transformation equations.
Why is shear strain tan theta and not theta?+
The displacement divided by the height is geometrically the tangent of the rotation of the vertical edge. The shortcut gamma = theta in radians is the small-angle approximation. At 15 degrees it is 2.3 percent below tan theta, and the error grows quickly after that.
Can shear strain be negative?+
Yes. The sign depends on the direction of shear relative to the coordinate axes you chose. A negative value means the angle between the reference axes increases instead of decreasing. For stress and energy only the magnitude matters, since tau = G gamma keeps the same sign.
How is shear strain different from normal strain?+
Normal strain is a change in length per original length along a line. Shear strain is a change in angle between two lines that started perpendicular. A shearing deformation can leave all lengths along the axes unchanged while still distorting the shape.
Why does shear strain vary across a shaft?+
Plane cross sections of a round shaft stay flat and rotate as rigid disks, so the sideways displacement of a point is proportional to its distance from the axis. The result is a strain that grows linearly from zero on the axis to the maximum at the surface.
What is the unit of shear strain for strain gauges?+
Gauge strains are usually reported in microstrain (millionths, written as micro epsilon). A shear strain of 600 microstrain is 0.0006, or 600 microradians. This calculator reports the rosette outputs in microstrain and the other modes as plain numbers.
Where does the maximum shear strain from a rosette come from?+
It is twice the radius R of the strain Mohr circle, gamma_max = 2R = e1 - e2, which is the difference of the principal strains. It acts on planes 45 degrees from the principal directions, and for the default readings equals 1000 microstrain.

What is the formula for shear strain?

Engineering shear strain is gamma = dx / h, the sideways displacement of one face divided by the perpendicular distance, which equals the tangent of the shear angle. For dx = 0.05 mm over h = 50 mm, gamma = 0.001.

What is the difference between engineering and tensor shear strain?

Engineering shear strain gamma is the total change in a right angle. Tensor shear strain epsilon_xy is half of it, gamma / 2, which is the symmetric off-diagonal term of the strain tensor. Stress uses gamma with tau = G gamma.

How do you calculate shear stress from shear strain?

In the elastic range, shear stress is tau = G gamma. With G = 79 GPa for steel and gamma = 0.001, tau = 79 MPa. This only holds up to the elastic limit of the material.

What is the shear strain in a twisted shaft?

On the surface of a solid round shaft, gamma = r theta / L, with r the radius, theta the angle of twist in radians and L the length. It drops linearly to zero on the axis. A 10 mm radius shaft 500 mm long twisted 1.5 degrees has a surface strain of 0.0005236.

Is shear strain in radians or degrees?

It is a dimensionless ratio, numerically equal to the tangent of the angle. For small angles the tangent is almost the angle in radians, so shear strain is often quoted in radians even though the angle itself may be measured in degrees.

How do you find shear strain from a strain gauge rosette?

For a 0/45/90 degree rectangular rosette, gamma_xy = 2 e45 - e0 - e90. Readings of 600, 500 and -200 microstrain give gamma_xy = 600 microstrain. The principal strains and maximum shear strain follow from the same three readings.

Why is shear strain tan theta and not theta?

Geometrically, the displacement divided by the height is the tangent of the angle the vertical edge rotates through. The small-angle shortcut theta is only accurate for small rotations; at 15 degrees it is 2.3 percent below tan theta.

Can shear strain be negative?

Yes. The sign depends on the direction of shear relative to the axes you chose. A negative value means the angle between the reference axes increases instead of decreasing. The magnitude is what matters for stress and energy.