Shear Modulus Calculator

Find a material's shear modulus (modulus of rigidity) from a shear test, from E and Poisson's ratio, or from a torsion test on a round shaft.

🔧 Shear Modulus Calculator
Shear force (F)
N
1005000
Sheared area (A)
mm²
Displacement (dx)
mm
0.510
Height (L)
mm
Material (illustrative values)
Young's modulus (E)
GPa
1300
Poisson's ratio (ν)
Torque (T)
N·m
Length (L)
mm
Diameter (d)
mm
Angle of twist (θ)
°
0.510
Shear modulus G
—
G in GPa
—
G in psi
—
Shear stress τ = F/A
—
Shear strain γ = dx/L
—
Shear angle
—
Stiffness F/dx
—
Closest material (illustrative)
—

Shear modulus G
—
G in MPa
—
G in psi
—
Bulk modulus K
—
Ratio G/E
—
E used
—
ν used
—
Closest material (illustrative)
—

Shear modulus G
—
G in GPa
—
Polar moment J
—
Surface shear stress
—
Surface shear strain
—
Twist in radians
—
Torsional stiffness T/θ
—
Closest material (illustrative)
—

🔧 What is the Shear Modulus?

The shear modulus, written G and also called the modulus of rigidity, is the ratio of shear stress to shear strain in the elastic range of a material. It measures how strongly a solid resists being deformed by forces that slide one layer over another, as opposed to being stretched or compressed. A large G means a stiff, rigid response to shear, like steel; a small G means an easily sheared material, like rubber or a gel. Its SI unit is the pascal, although values for solids are normally quoted in gigapascals or megapascals.

The shear modulus is a key design parameter wherever twisting or sliding occurs. It sets how far a drive shaft twists under torque, how much a rubber bearing or vibration isolator deflects sideways, how a bolted or glued joint distorts, and how fast shear waves travel through rock and metal. Geophysicists use it to interpret seismic data, structural engineers use it for torsion and shear deflection, and materials scientists use it as one of the basic elastic constants alongside Young's modulus, the bulk modulus and Poisson's ratio. For an isotropic material only two of these constants are independent, which is why G can be found from E and nu.

Several details prevent common errors. The direct definition gives a secant value, and it is only meaningful while the response is linear. G is not the same as the shear strength, which is the stress at which the material fails. It is also not the same as Young's modulus, even though the two are related by G = E / (2 (1 + nu)); for most metals G is roughly 35 to 40 percent of E. And the relation with E and nu applies to isotropic materials only: wood, composites and single crystals have several different shear moduli depending on direction.

This calculator offers three routes to G. The shear test mode uses force, area, displacement and height. The E and nu mode converts from the more commonly tabulated Young's modulus and Poisson ratio, and also returns the bulk modulus. The torsion test mode uses torque, length, diameter and twist angle of a solid round shaft. Each result is compared with a short illustrative list of materials, and a chart shows the underlying relationship. For the opposite problem, the twist of a shaft of known G, use the angle of twist calculator.

📐 Formula

G  =  τ / γ  =  F L / (A dx)  =  E / (2 (1 + ν))  =  T L / (J θ)
G = shear modulus; τ = F / A is the shear stress; γ = dx / L is the shear strain
F = shear force (N), A = sheared area (mm²), dx = sideways displacement and L = height, both in mm; N and mm² give MPa
E, ν = Young's modulus and Poisson's ratio of an isotropic material; the bulk modulus is K = E / (3 (1 − 2ν))
T, L, θ = torque, length and twist angle (radians) of a round shaft; J = π d⁴ / 32 is its polar moment of area
Example: E = 200 GPa and ν = 0.30 give G = 200 / 2.6 = 76.92 GPa

📖 How to Use This Calculator

Steps

1
Choose how you know G. Pick Shear test if you have force, area and displacement, From E and nu if you know Young's modulus and Poisson's ratio, or Torsion test if you twisted a round shaft.
2
Enter the measurements. Use newtons, square millimetres and millimetres for the shear test, GPa for E, or torque in N·m with lengths in mm and the twist in degrees. A material preset fills E and nu for you.
3
Read G and the chart. The main box gives G in MPa or GPa. Below are G in other units, the supporting stress and strain, the closest illustrative material and a chart of the relationship.

💡 Example Calculations

Example 1 — Elastomer Pad in Shear

F = 1000 N on a 2000 mm² pad, displacement 2 mm over a 10 mm thickness

1
τ = F / A = 1000 / 2000 = 0.5000 MPa
2
γ = dx / L = 2 / 10 = 0.2000 (shear angle 11.31°)
3
G = 0.5 / 0.2 = 2.500 MPa = 0.002500 GPa = 362.6 psi, which is a firm elastomer, closest to the soft rubber entry in the illustrative list
Shear modulus = 2.500 MPa
Try this example →

Example 2 — Steel from E and Poisson's Ratio

E = 200 GPa, ν = 0.30 (illustrative steel)

1
2 (1 + ν) = 2 × 1.30 = 2.60
2
G = 200 / 2.60 = 76.92 GPa = 76923 MPa, and G / E = 0.3846
3
The bulk modulus is K = 200 / (3 × 0.4) = 166.7 GPa. Handbooks often quote about 79 GPa for steel, so the exact figure depends on the alloy.
Shear modulus = 76.92 GPa
Try this example →

Example 3 — Aluminium from E and Poisson's Ratio

E = 69 GPa, ν = 0.33 (illustrative aluminium)

1
2 (1 + ν) = 2 × 1.33 = 2.66
2
G = 69 / 2.66 = 25.94 GPa, with G / E = 0.3759
3
K = 69 / (3 × 0.34) = 67.65 GPa. Aluminium twists about three times more than steel under the same torque and geometry.
Shear modulus = 25.94 GPa
Try this example →

Example 4 — Torsion Test on a Round Bar

T = 100 N·m, L = 500 mm, d = 20 mm, twist 2.5°

1
J = π × 20⁴ / 32 = 15708 mm⁴ and θ = 2.5° = 0.04363 rad
2
G = T L / (J θ) = 100000 × 500 / (15708 × 0.04363) = 72.95 GPa
3
The surface stress is T r / J = 63.66 MPa and the surface strain is 0.0008727, which divide to the same G. The torsional stiffness is 2292 N·m/rad.
Shear modulus = 72.95 GPa
Try this example →

❓ Frequently Asked Questions

What is the formula for shear modulus?+
Shear modulus is G = tau / gamma, the shear stress divided by the shear strain. With tau = F / A and gamma = dx / L, G = F L / (A dx). For F = 1000 N, A = 2000 mm2, dx = 2 mm and L = 10 mm, G = 2.5 MPa.
How do you calculate shear modulus from Young's modulus?+
For isotropic materials G = E / (2 (1 + nu)). With E = 200 GPa and nu = 0.30, G = 76.92 GPa. With E = 69 GPa and nu = 0.33, G = 25.94 GPa. The relation does not hold for anisotropic materials such as wood or fibre composites.
How do you find shear modulus from a torsion test?+
Twist a round bar and measure the torque T, length L and twist angle theta in radians. Then G = T L / (J theta), where J = pi d^4 / 32 for a solid shaft. T = 100 N m, L = 500 mm, d = 20 mm and theta = 2.5 degrees give G = 72.95 GPa.
What are the units of shear modulus?+
The units are those of pressure, pascals in SI. Values for solids are usually written in gigapascals (GPa) or megapascals (MPa), and in psi or ksi in US practice. One GPa equals 1000 MPa or about 145,038 psi.
What is a typical shear modulus for steel?+
Steel is commonly quoted at about 79 GPa, and E / (2 (1 + nu)) with E = 200 GPa and nu = 0.3 gives 76.9 GPa. Values depend on the alloy, so the figures on this page are illustrative and not for design.
Is shear modulus the same as modulus of rigidity?+
Yes. Shear modulus, modulus of rigidity and the second Lame parameter are all names for G. It describes resistance to shape change at constant volume, whereas Young's modulus describes resistance to stretching along an axis.
Why is shear modulus smaller than Young's modulus?+
For positive Poisson's ratio the factor 2 (1 + nu) lies between 2 and 3, so G is between one half and one third of E. Shearing a solid is easier than stretching it, so the stiffness against sliding is lower than against elongation.
Can shear modulus be zero or negative?+
An ideal fluid at rest has a shear modulus of zero because it cannot hold a static shear stress. A stable solid needs G greater than zero. Soft gels and rubbers have very small values, starting around a fraction of a megapascal.
What is the difference between shear modulus and shear strength?+
The shear modulus is a stiffness, the slope of the elastic part of the shear stress-strain curve. The shear strength is the stress at which the material yields or fails in shear. A material can be stiff but weak, or soft but strong.
How is G related to the bulk modulus and Poisson's ratio?+
For isotropic materials K = 2 G (1 + nu) / (3 (1 - 2 nu)), and nu = (3K - 2G) / (2 (3K + G)). Knowing any two elastic constants fixes the rest. The elastic constants calculator performs all of these conversions.
Why does the shear test give a secant value?+
The calculator divides one stress by one strain, so it returns the average slope from the origin to your data point. If the material is not linear, such as rubber at large strain, that secant value differs from the initial tangent modulus.
What is the torsional stiffness of a shaft?+
The torsional stiffness is the torque per unit twist angle, k = T / theta = G J / L. It rises with the shear modulus and with the fourth power of the diameter, and falls with length. The torsion mode reports it in N m per radian.

What is the formula for shear modulus?

Shear modulus is G = tau / gamma, the shear stress divided by the shear strain. With tau = F / A and gamma = dx / L, G = F L / (A dx). For F = 1000 N, A = 2000 mm2, dx = 2 mm and L = 10 mm, G = 2.5 MPa.

How do you calculate shear modulus from Young's modulus?

For isotropic materials G = E / (2 (1 + nu)). Steel with E = 200 GPa and nu = 0.30 gives G = 76.92 GPa. Aluminium with E = 69 GPa and nu = 0.33 gives 25.94 GPa.

How do you find shear modulus from a torsion test?

Twist a round bar and measure the torque T, length L and angle theta in radians. Then G = T L / (J theta), where J = pi d^4 / 32 for a solid shaft. T = 100 N m, L = 500 mm, d = 20 mm and theta = 2.5 degrees give G = 72.95 GPa.

What are the units of shear modulus?

The units are those of pressure, pascals in SI. Values for solids are usually written in gigapascals (GPa) or megapascals (MPa), and in psi or ksi in US practice. 1 GPa = 1000 MPa = 145,038 psi.

What is a typical shear modulus for steel?

Steel is commonly quoted at about 79 GPa, and E / (2 (1 + nu)) with E = 200 GPa and nu = 0.3 gives 76.9 GPa. Values depend on the alloy, so the figures here are illustrative and not for design.

Is shear modulus the same as modulus of rigidity?

Yes. Shear modulus, modulus of rigidity and the second Lame parameter are all names for G. It describes resistance to shape change at constant volume, unlike Young's modulus, which describes resistance to stretching.

Why is shear modulus smaller than Young's modulus?

For positive Poisson's ratio the factor 2 (1 + nu) is between 2 and 3, so G is between one half and one third of E. Shearing a solid is easier than stretching it, because it does not have to change atomic spacing as much.

Can shear modulus be zero?

Ideal fluids have a shear modulus of zero because they cannot hold a static shear stress. Soft gels and rubbers have very small values, from a fraction of a megapascal upward, while diamond is near 478 GPa.