Rotational Stiffness Calculator

Find the torsional spring constant of a spring or shaft, the torque and energy at a given twist, and the natural frequency with a load.

🔧 Rotational Stiffness Calculator
Applied torque (T)
0.5100
Twist angle (θ)
Rotational stiffness (k)
N·m/rad
0.5100
I know the
Twist angle (θ)
N·m
Material (typical values)
Shear modulus (G)
GPa
Section
Outer diameter (D)
mm
Inner diameter (d)
mm
Length (L)
mm
502000
Applied torque (T)
N·m
Rotational stiffness (k)
N·m/rad
0.5100
Inertia given as
Moment of inertia (I)
kg·m²
Disk mass (m)
kg
Disk radius (R)
m
Rotational stiffness (k)
—
Per degree
—
In lbf·ft per radian
—
Twist angle
—
Torque used
—
Energy stored
—

Torque (T)
—
Torque in lbf·ft
—
Twist angle
—
Twist angle in degrees
—
Revolutions
—
Energy stored
—

Shaft stiffness (k = GJ/L)
—
Polar moment J
—
Per degree
—
Twist under the torque
—
Surface shear stress
—
Compliance (1/k)
—

Natural frequency
—
Angular frequency (ωn)
—
Period
—
In cycles per minute
—
Inertia used
—
Stiffness used
—

🔧 What is Rotational Stiffness?

Rotational stiffness, also called torsional stiffness or the torsional spring constant, is the torque a spring, shaft or joint needs per unit of twist. It is written k = T/θ and measured in newton metres per radian. It is the angular counterpart of the linear spring constant in Hooke's law: a linear spring gives force proportional to stretch, and a torsional spring gives torque proportional to angle. Because the relation is linear, the energy stored is ½ k θ², and a mass attached to the spring oscillates with a natural angular frequency of √(k/I).

The quantity appears in many places. Clock hairsprings, door hinges, clothespins and mousetraps are torsional springs. Car anti-roll bars, drive shafts, steering columns and motor couplings behave as torsional springs through their material stiffness. Torsion pendulums and the balance in a Cavendish experiment rely on a thin fibre of known k. In robotics and control, series elastic actuators and flexible joints are modelled with k, and in machine design the twist of a shaft under load is a common stiffness limit alongside strength.

A few details matter. A round shaft of length L has k = G J / L, where G is the shear modulus and J is the polar second moment of area, so stiffness rises with the fourth power of the diameter and falls in inverse proportion to the length. The angle must be in radians when you use k in N·m/rad. The model is linear, so it holds only within the elastic range of the material. Helical torsion springs have their own formulas based on wire diameter and coil count, which this page does not cover. For the section property alone see the polar moment of inertia calculator, and for the linear version see the Hooke's law calculator.

This calculator offers four modes. Spring constant finds k from a measured torque and angle. Torque and energy uses a known k to find the torque for an angle, or the angle for a torque, with the elastic energy. Shaft computes k = G J / L for solid and hollow round shafts with the twist and surface shear stress for an applied torque. Natural frequency combines k with a moment of inertia (or a solid disk) to give the oscillation frequency. Each mode has its own chart.

📐 Formula

k  =  T / θ   |   kshaft  =  G J / L
k = rotational stiffness (N·m/rad); to get N·m per degree multiply by π/180
T = torque (N·m); lbf·ft is multiplied by 1.3558179 and lbf·in by 0.1129848
θ = twist angle in radians (degrees × π/180, revolutions × 2π)
U = ½ k θ² = ½ T θ, the elastic energy stored (J)
G = shear modulus (Pa); 79.3 GPa for steel, 25.5 GPa for aluminium, 44.7 GPa for copper
J = polar second moment of area: π D4 / 32 for a solid round shaft, π ( D4 − d4 ) / 32 for a hollow one
L = shaft length; the twist under torque T is θ = T L / (G J) and the surface shear stress is τ = T (D/2) / J
Natural frequency: ωn = √( k / I ), fn = ωn / 2π, and I = ½ m R² for a solid disk
Example: T = 5 N·m and θ = 30° = 0.5236 rad gives k = 9.549 N·m/rad

📖 How to Use This Calculator

Steps

1
Choose a mode. Pick Spring constant to find k from a torque and angle, Torque and energy to use a known k, Shaft to compute k = GJ/L, or Natural frequency to add an inertia.
2
Enter the torque, angle or shaft data. Type the torque and the angle, choosing their units (the menus only tell the calculator how to read what you typed), or the shaft diameter, length and shear modulus, or k and the moment of inertia.
3
Read the result and chart. See the stiffness, torque, energy or frequency in the result boxes. The chart shows torque against angle, stiffness against length or frequency against inertia, with your point marked.

💡 Example Calculations

Example 1 — Torsion Spring Test

A torque of 5 N·m twists a spring by 30 degrees

1
θ = 30 × π / 180 = 0.5236 rad
2
k = T / θ = 5 / 0.5236 = 9.549 N·m/rad, or 0.16667 N·m per degree
3
U = ½ T θ = 0.5 × 5 × 0.5236 = 1.309 J
k = 9.549 N·m/rad, energy = 1.309 J
Try this example →

Example 2 — Torque in lbf·ft, Angle in Revolutions

10 lbf·ft turns a spring half a revolution

1
T = 10 × 1.3558179 = 13.56 N·m and θ = 0.5 × 2π = 3.142 rad (180 degrees)
2
k = 13.558 / 3.142 = 4.316 N·m/rad, which is 3.183 lbf·ft per radian
3
U = ½ × 13.558 × 3.142 = 21.30 J
k = 4.316 N·m/rad
Try this example →

Example 3 — Torque Needed for a Given Twist

A spring of k = 12 N·m/rad is wound through 90 degrees

1
θ = 90° = 1.571 rad = 0.25 rev
2
T = k θ = 12 × 1.571 = 18.85 N·m (13.90 lbf·ft)
3
U = ½ k θ² = 0.5 × 12 × 1.571² = 14.80 J
Torque = 18.85 N·m, energy = 14.80 J
Try this example →

Example 4 — Angle for a Given Torque

A small spring of k = 0.5 N·m/rad carries a torque of 0.25 N·m

1
θ = T / k = 0.25 / 0.5 = 0.5000 rad
2
In degrees, 0.5 × 180 / π = 28.65°, which is 0.07958 revolutions
3
U = ½ × 0.25 × 0.5 = 0.06250 J
Twist = 28.65°, energy = 0.06250 J
Try this example →

Example 5 — Solid Steel Shaft

Steel (G = 79.3 GPa), diameter 25 mm, length 500 mm, torque 100 N·m

1
J = π × 254 / 32 = 38,349.5 mm4
2
k = G J / L = 79,300 × 38,349.5 / 500 = 6,082,200 N·mm/rad = 6,082.2 N·m/rad
3
Twist = 100 / 6082.2 = 0.01644 rad = 0.94202° and the surface stress is 100,000 × 12.5 / 38,349.5 = 32.59 MPa
k = 6,082.2 N·m/rad, twist = 0.94202°
Try this example →

Example 6 — Hollow Aluminium Tube

Aluminium (G = 25.5 GPa), D = 50 mm, d = 40 mm, length 1000 mm, torque 200 N·m

1
J = π ( 504 − 404 ) / 32 = π × 3,690,000 / 32 = 362,264.9 mm4
2
k = 25,500 × 362,264.9 / 1000 / 1000 = 9,237.8 N·m/rad
3
Twist = 200 / 9237.8 = 0.02165 rad = 1.240° and the surface stress is 200,000 × 25 / 362,264.9 = 13.80 MPa
k = 9,237.8 N·m/rad, twist = 1.240°
Try this example →

Example 7 — Torsion Pendulum

k = 2 N·m/rad with a moment of inertia of 0.005 kg·m²

1
ωn = √( 2 / 0.005 ) = √400 = 20.00 rad/s
2
fn = 20 / 2π = 3.183 Hz, which is 190.99 cycles per minute
3
Period = 1 / 3.183 = 0.31416 s
Natural frequency = 3.183 Hz
Try this example →

Example 8 — Disk on a Torsion Wire

k = 10 N·m/rad carrying a solid disk of 2 kg and radius 0.1 m

1
I = ½ m R² = 0.5 × 2 × 0.01 = 0.01000 kg·m²
2
ωn = √( 10 / 0.01 ) = √1000 = 31.62 rad/s
3
fn = 31.62 / 2π = 5.033 Hz and the period is 0.19869 s
Natural frequency = 5.033 Hz
Try this example →

❓ Frequently Asked Questions

What is rotational stiffness?+
Rotational (torsional) stiffness is the torque needed per unit of twist, k = T / theta, measured in N m per radian. A stiffer spring or shaft needs more torque for the same angle. It is the angular analogue of the linear spring constant.
How do you calculate the torsional spring constant?+
Divide the applied torque by the angle of twist in radians. A torque of 5 N m turning a spring by 30 degrees (0.5236 rad) gives k = 5 / 0.5236 = 9.549 N m/rad, or 0.1667 N m per degree.
What is the formula for the torsional stiffness of a shaft?+
k = G J / L, where G is the shear modulus, J is the polar second moment of area (pi D to the fourth over 32 for a solid round shaft) and L is the length. A 25 mm steel shaft 500 mm long has k of about 6,082 N m/rad.
How is energy stored in a torsional spring?+
The elastic energy is U = 1/2 k theta squared = 1/2 T theta, with theta in radians. A spring of 12 N m/rad twisted by 90 degrees stores 14.80 J.
How do I find the natural frequency of a torsional system?+
omega_n = sqrt(k / I) in rad/s, and f = omega_n / 2 pi. For k = 2 N m/rad and I = 0.005 kg m2 the frequency is 20 rad/s, or 3.183 Hz, with a period of 0.314 s.
What is the unit of torsional stiffness?+
The SI unit is N m per radian (N m/rad), equivalent to kg m2 per s2. Other common units are N m per degree, lbf ft per degree and lbf in per degree. Multiply N m/rad by 0.01745 to get N m per degree.
Does a longer shaft have more or less torsional stiffness?+
Less. Stiffness is inversely proportional to length, so doubling the length of a shaft halves k. That is why long drive shafts twist more than short ones for the same torque.
What shear modulus should I use for steel?+
Use about 79.3 GPa for steel at room temperature. Aluminium is about 25.5 GPa and copper about 44.7 GPa. Alloys and temperature change these values, so check your material data sheet for important work.
How do I combine torsional springs in series or parallel?+
In parallel (sharing the same twist) the stiffnesses add, k = k1 + k2. In series (sharing the same torque) the compliances add, 1 / k = 1 / k1 + 1 / k2. This calculator handles one spring or shaft at a time.
How is this different from the polar moment of inertia calculator?+
The polar moment of inertia calculator gives the section property J of a shaft. This page uses J together with the shear modulus and length to give the torsional stiffness, twist angle, stored energy and vibration frequency.
Does the amplitude change the torsional natural frequency?+
Not for a linear spring. The period of a torsion pendulum is independent of amplitude as long as the torque stays proportional to the angle and damping is negligible.

What is rotational stiffness?

Rotational (torsional) stiffness is the torque needed per unit of twist, k = T / theta, measured in N m per radian. A stiffer spring or shaft needs more torque for the same angle. It is the angular analogue of the linear spring constant.

How do you calculate the torsional spring constant?

Divide the applied torque by the angle of twist in radians. A torque of 5 N m turning a spring by 30 degrees (0.5236 rad) gives k = 5 / 0.5236 = 9.549 N m/rad, or 0.1667 N m per degree.

What is the formula for the torsional stiffness of a shaft?

k = G J / L, where G is the shear modulus, J is the polar second moment of area (pi d to the fourth over 32 for a solid round shaft) and L is the length. A 25 mm steel shaft 500 mm long has k of about 6,082 N m/rad.

How is energy stored in a torsional spring?

The elastic energy is U = 1/2 k theta squared = 1/2 T theta, with theta in radians. A spring of 12 N m/rad twisted by 90 degrees stores 14.80 J.

How do I find the natural frequency of a torsional system?

omega_n = sqrt(k / I) in rad/s, and f = omega_n / 2 pi. For k = 2 N m/rad and I = 0.005 kg m2 the frequency is 20 rad/s, or 3.183 Hz, with a period of 0.314 s.

What is the unit of torsional stiffness?

The SI unit is N m per radian (N m/rad), equivalent to kg m2 per s2. Other common units are N m per degree, lbf ft per degree and lbf in per degree. Multiply N m/rad by 0.01745 to get N m per degree.

Does a longer shaft have more or less torsional stiffness?

Less. Stiffness is inversely proportional to length, so doubling the length of a shaft halves k. That is why long drive shafts twist more than short ones for the same torque.

What shear modulus should I use for steel?

Use about 79.3 GPa for steel at room temperature. Aluminium is about 25.5 GPa and copper about 44.7 GPa. Alloys and temperature change these values, so check your material data sheet for important work.

How do I combine torsional springs in series or parallel?

In parallel (sharing the same twist) the stiffnesses add, k = k1 + k2. In series (sharing the same torque) the compliances add, 1 / k = 1 / k1 + 1 / k2. This calculator handles one spring or shaft at a time.

How is this different from the polar moment of inertia calculator?

The polar moment of inertia is only the section property J of a shaft. This page uses J together with the shear modulus and length to give the torsional stiffness, twist angle, stored energy and vibration frequency.

Does the amplitude change the torsional natural frequency?

Not for a linear spring. The period of a torsion pendulum is independent of amplitude as long as the torque stays proportional to the angle and damping is negligible.