Poisson's Ratio Calculator

Find Poisson's ratio from measured length and width changes or from E and G, and see how it controls the volume change of a stretched sample.

↔️ Poisson's Ratio Calculator
Original length (L0)
mm
Stretched length (L)
mm
Original width (W0)
mm
Deformed width (W)
mm
Axial strain (ε)
%
010
Poisson's ratio (ν)
Original width (optional)
mm
Young's modulus (E)
GPa
1300
Shear modulus (G)
GPa
1150
Poisson's ratio ν
—
Axial strain
—
Lateral strain
—
Axial strain (%)
—
Lateral strain (%)
—
Volume change
—
Valid isotropic range?
—
Behaviour
—

Volume change (exact)
—
Small-strain estimate
—
Lateral strain
—
Factor (1 − 2ν)
—
Volume ratio V/V0
—
Deformed width
—
Volume
—
Behaviour
—

Poisson's ratio ν
—
Valid isotropic range?
—
Bulk modulus K
—
Ratio G/E
—
E used
—
G used
—
Behaviour
—
Valid G for this E
—

↔️ What is Poisson's Ratio?

Poisson's ratio is the negative ratio of the transverse strain to the axial strain when a material is loaded along one direction. Stretch a rubber band and it gets thinner; compress a block and it bulges sideways. Poisson's ratio, written nu (the Greek letter), quantifies that sideways response. It is dimensionless, and for most everyday solids it falls between 0 and 0.5. A value of 0.3, typical of steel, means that for every 1 percent of stretch the cross section shrinks by 0.3 percent in each lateral direction.

The ratio is used constantly in mechanics. It links the elastic constants of isotropic materials, so that the shear modulus, the bulk modulus and the Lame parameter can all be computed once E and nu are known. It governs how the volume of a stretched sample changes, how pressure vessels bulge, how pipes and bolts react to axial load, and how a rubber seal pushes against its housing. It also controls the speeds of waves in solids, since the ratio of P-wave to S-wave speed depends on nu alone. In geotechnical and rock mechanics, it sets the lateral earth pressure at rest in an elastic soil.

A few ideas are worth keeping straight. The limits are tied to stability: a stable isotropic solid has nu between -1 and 0.5, because the shear modulus and bulk modulus must both stay positive. The upper limit, 0.5, is the incompressible case, where no volume change occurs under small deformations; rubber and water-saturated clay approach it. The lower side is the auxetic region, where nu is negative and the material swells in width when stretched, as in some foams and engineered lattices. And the definition assumes small, elastic, uniform strains; during plastic flow of metals the apparent ratio tends toward 0.5 because plastic deformation conserves volume.

The calculator has three modes. From dimensions computes the ratio from the measured length and width before and after loading, and estimates the volume change. Volume change starts from an axial strain and a known nu and returns both the exact and the first-order volume change. From E and G uses nu = E / (2G) - 1 and checks whether the result is physically possible. Each mode classifies the result as auxetic, typical, near incompressible or outside the isotropic range.

📐 Formula

ν  =  −εlat / εaxial  =  E / (2G) − 1
εaxial = (L − L0) / L0, the strain along the load; εlat = (W − W0) / W0, the strain across it
ν = Poisson's ratio, dimensionless; stable isotropic solids have −1 < ν < 0.5
E, G = Young's modulus and shear modulus (same units), valid for isotropic materials
Volume change: ΔV/V = (1 + ε)(1 − νε)² − 1 ≈ ε (1 − 2ν) for small strain
Example: εaxial = 0.002 and εlat = −0.0006 give ν = 0.30

📖 How to Use This Calculator

Steps

1
Choose the starting data. Pick From dimensions if you measured length and width, Volume change if you know nu and the axial strain, or From E and G if you know the two moduli.
2
Enter the values. Type the original and deformed length and width in mm, or the axial strain in percent and the ratio nu, or E and G in GPa. A square or round cross section is assumed for the volume estimate.
3
Read nu, the classification and the chart. The result box shows the ratio or the volume change. Check whether it falls in the valid isotropic range and whether it is auxetic, typical or near the incompressible limit, then study the chart for your mode.

💡 Example Calculations

Example 1 — Steel-Like Bar in Tension

L0 = 100 mm stretched to 100.2 mm, width 20 mm shrinks to 19.988 mm

1
Axial strain = 0.2 / 100 = 0.002000 and lateral strain = (19.988 − 20) / 20 = −0.0006000
2
ν = −(−0.0006) / 0.002 = 0.3000, a typical value for many metals
3
Volume change = 1.002 × 0.9994² − 1 = 0.07980 %, assuming both lateral directions contract equally
Poisson's ratio = 0.3000
Try this example →

Example 2 — Auxetic Foam

L0 = 50 mm stretched to 51 mm, width 30 mm grows to 30.3 mm

1
Axial strain = 1 / 50 = 0.02000 and lateral strain = 0.3 / 30 = +0.01000
2
ν = −0.01 / 0.02 = −0.5000, which is inside the allowed range but negative, so the sample is auxetic
3
Volume change = 1.02 × 1.01² − 1 = 4.050 %, noticeably more than the 2 % stretch alone. The foam dimensions are hypothetical.
Poisson's ratio = −0.5000 (auxetic)
Try this example →

Example 3 — Volume Change of a Stretched Metal Bar

Axial strain 1 %, ν = 0.3, original width 20 mm

1
Lateral strain = −0.3 × 1 % = −0.3000 %, so the width becomes 20 × 0.997 = 19.940 mm
2
Exact volume change = 1.01 × 0.997² − 1 = 0.3949 %
3
The small-strain estimate ε (1 − 2ν) = 1 % × 0.4 = 0.4000 %, a close match at this small strain
Volume change = 0.3949 % (volume ratio 1.0039)
Try this example →

Example 4 — Rubber-Like Material at Large Strain

Axial strain 10 %, ν = 0.49, original width 20 mm

1
Lateral strain = −0.49 × 10 % = −4.900 %, width 19.020 mm
2
Exact volume change = 1.1 × 0.951² − 1 = −0.5159 %, a small shrinkage
3
The first-order estimate ε (1 − 2ν) = 10 % × 0.02 = +0.2000 % even has the wrong sign. For near incompressible materials at 10 % strain the exact formula is needed, and the linear nu model itself is only approximate.
Volume change = −0.5159 %
Try this example →

Example 5 — From Young's Modulus and Shear Modulus

E = 200 GPa and G = 80 GPa

1
ν = E / (2G) − 1 = 200 / 160 − 1 = 0.2500
2
G / E = 0.4000, which is inside the valid isotropic band, so the pair is physically consistent
3
K = E G / (3 (3G − E)) = 16000 / 120 = 133.3 GPa. For this E, any G from 66.67 to 100.0 GPa gives a non-negative nu.
Poisson's ratio = 0.2500, K = 133.3 GPa
Try this example →

❓ Frequently Asked Questions

What is the formula for Poisson's ratio?+
Poisson's ratio is nu = -(lateral strain) / (axial strain). With axial strain +0.002 and lateral strain -0.0006, nu = 0.0006 / 0.002 = 0.30. The minus sign makes the ratio positive for materials that contract sideways when stretched.
What is the range of Poisson's ratio?+
For a stable isotropic linear elastic solid, nu lies between -1 and 0.5. Most materials fall between 0 and 0.5, with steels near 0.3 and rubber near 0.5. Anisotropic materials can exceed these limits in particular directions.
What does a negative Poisson's ratio mean?+
A negative value means the material gets wider when stretched. Such auxetic materials include some foams, folded sheets and re-entrant lattices. In a dimension test it shows up as lateral and axial strains with the same sign.
What is Poisson's ratio for an incompressible material?+
An incompressible isotropic material has nu = 0.5, because the lateral contraction exactly offsets the axial stretch and the volume does not change at small strain. Rubber and water-saturated clay come close to this limit.
How do you find Poisson's ratio from E and G?+
For isotropic materials nu = E / (2G) - 1. With E = 200 GPa and G = 80 GPa, nu = 200 / 160 - 1 = 0.25. A result outside -1 to 0.5 means the pair is not consistent with an isotropic solid, so recheck the data.
How does Poisson's ratio affect volume change?+
For small axial strain epsilon the volume changes by epsilon (1 - 2 nu). With nu = 0.3 and a 1 percent stretch, the volume rises by about 0.4 percent. At nu = 0.5 it does not change at all, and for a negative nu it grows faster than the length.
Why is the exact volume change different from epsilon (1 - 2 nu)?+
The shortcut keeps only first-order terms. The exact change is (1 + epsilon)(1 - nu epsilon)^2 - 1. For nu = 0.49 and 10 percent strain the exact value is -0.52 percent while the shortcut says +0.20 percent, so use the exact form at larger strain.
What is a typical Poisson's ratio for steel?+
Steels are often quoted near 0.27 to 0.30, aluminium alloys near 0.33 and many glasses around 0.2. These are illustrative figures only, since the exact value depends on composition, processing and temperature.
Can Poisson's ratio be greater than 0.5?+
Not for an isotropic solid, since that would make the bulk modulus negative. Anisotropic materials such as some composites, crystals or folded structures can show a ratio above 0.5 for particular pairs of directions, but that is a different, direction-dependent quantity.
Why do I get a different value in the plastic range?+
Plastic deformation of metals conserves volume, so the effective ratio approaches 0.5 once most of the strain is plastic. Elastic values near 0.3 apply only in the elastic range, and the calculator assumes small strain behaviour.
How accurate is a Poisson's ratio from caliper measurements?+
Not very. Lateral changes are tiny, for example 12 micrometres on a 20 mm width. A caliper resolving 10 micrometres would leave an uncertainty of order 80 percent in nu, so strain gauges or extensometers are used for real tests.
How does Poisson's ratio relate to the other elastic constants?+
G = E / (2 (1 + nu)) and K = E / (3 (1 - 2 nu)) for isotropic materials, so any two constants determine the rest. The elastic constants calculator on this site converts between all six common forms.

What is the formula for Poisson's ratio?

Poisson's ratio is nu = -(lateral strain) / (axial strain). With axial strain +0.002 and lateral strain -0.0006, nu = 0.0006 / 0.002 = 0.30. The minus sign makes the ratio positive for materials that contract sideways when stretched.

What is the range of Poisson's ratio?

For a stable isotropic linear elastic solid, nu lies between -1 and 0.5. Most materials fall between 0 and 0.5, steels near 0.3, rubber near 0.5. Anisotropic materials can exceed these limits in particular directions.

What does a negative Poisson's ratio mean?

A negative value means the material gets wider when stretched. Such auxetic materials include some foams, folded sheets and re-entrant lattices. In a dimension test it shows up as lateral and axial strains with the same sign.

What is Poisson's ratio for an incompressible material?

An incompressible isotropic material has nu = 0.5 exactly, because the lateral contraction then perfectly offsets the axial stretch and the volume does not change at small strain. Rubber and water-saturated soils come close to this limit.

How do you find Poisson's ratio from E and G?

For isotropic materials nu = E / (2G) - 1. With E = 200 GPa and G = 80 GPa, nu = 200 / 160 - 1 = 0.25. A result outside -1 to 0.5 means the pair is not consistent with an isotropic solid.

How does Poisson's ratio affect volume change?

For small axial strain epsilon, the volume changes by epsilon (1 - 2 nu). With nu = 0.3 and epsilon = 1 percent the volume rises about 0.4 percent. At nu = 0.5 it does not change, and for nu above 0.5 it would shrink.

Why is the exact volume change different from epsilon (1 - 2 nu)?

The shortcut keeps only first-order terms. The exact change is (1 + epsilon)(1 - nu epsilon)^2 - 1, which for nu = 0.49 and 10 percent strain is -0.52 percent while the shortcut says +0.20 percent. The shortcut is reliable only for strains of a few percent or less.

What is a typical Poisson's ratio for steel?

Steels are often quoted near 0.27 to 0.30, aluminium alloys near 0.33 and many glasses around 0.2. These are illustrative figures; exact values depend on composition and temperature.