Elastic Constants Calculator

Give any two isotropic elastic constants and get Young's, shear and bulk modulus, Poisson's ratio, Lame's first parameter and the P-wave modulus.

🧮 Elastic Constants Calculator
Material preset (illustrative values)
Modulus unit (values are not converted)
First known constant
Second known constant
Young's modulus E
—
Shear modulus G
—
Bulk modulus K
—
Poisson's ratio ν
—
Lamé parameter λ
—
P-wave modulus M
—
Validity
—
Check
—

🧮 What are the Elastic Constants?

Elastic constants are the numbers that describe how a solid deforms elastically under load. For an isotropic material, one that behaves the same in every direction, there are six commonly used constants: Young's modulus E (stiffness in tension), the shear modulus G (stiffness in shear), the bulk modulus K (stiffness against uniform compression), Poisson's ratio nu (lateral contraction per axial stretch), Lame's first parameter lambda, and the P-wave modulus M (stiffness in uniaxial strain). Surprisingly, only two of them are independent. If you know any two, you can derive the other four.

This matters because different fields quote different constants. Mechanical and civil engineers usually work with E and nu. Geophysicists and acousticians prefer K and G, or the wave speeds that come from M and G. Continuum mechanics texts and finite element software often use the Lame parameters lambda and mu (where mu is simply G). Material data sheets might give only E and G, or only K. A converter lets you move between these without hunting for formulas, check data from two sources for consistency, and fill in the constants that a simulation package asks for.

Several cautions apply. All the relations assume a linear, isotropic, homogeneous material; they do not hold for wood, laminates, rolled sheet or single crystals, which need more constants. A set of constants is only physically meaningful if both K and G are positive, which is equivalent to -1 < nu < 0.5 and E > 0; the calculator performs this validity check and tells you when a pair cannot describe a stable solid. The pair E and M is special, since it leads to a quadratic equation and two possible answers. Finally, the numbers in the material presets are illustrative textbook figures for typical alloys, not design values.

Pick your two known constants, enter the values in the unit you prefer (GPa, MPa, psi, ksi or million psi) and the calculator returns all six in that same unit, plus a table that also shows GPa, MPa and psi. A chart shows how the moduli, measured relative to E, vary with Poisson's ratio, with your material marked. For specialised work on single quantities see the shear modulus, bulk modulus and Poisson's ratio calculators.

📐 Formula

E = 9KG / (3K + G),   ν = (3K − 2G) / (2 (3K + G)),   λ = K − 2G/3,   M = K + 4G/3
E = Young's modulus, G = shear modulus (also μ), K = bulk modulus, all in the same unit
ν = Poisson's ratio (dimensionless), λ = Lamé's first parameter, M = P-wave modulus = λ + 2G
From E and ν: G = E / (2 (1 + ν)), K = E / (3 (1 − 2ν)), λ = Eν / ((1 + ν)(1 − 2ν))
From E and G: K = E G / (3 (3G − E)); from K and ν: G = 3K (1 − 2ν) / (2 (1 + ν))
From λ and G: K = λ + 2G/3; from E and M: S = √(E² + 9M² − 10EM), K = (3M − E + S) / 6, G = (3M + E − S) / 8
Validity: K > 0 and G > 0, equivalent to −1 < ν < 0.5
Example: E = 200 GPa and ν = 0.30 give G = 76.92, K = 166.67, λ = 115.38 and M = 269.23 GPa

📖 How to Use This Calculator

Steps

1
Choose the two constants you know. Select the first and second known constant from the drop-downs, or pick a material preset, which fills E and Poisson's ratio for you.
2
Enter their values and the unit. Type the two numbers and choose GPa, MPa, psi, ksi or Mpsi for the moduli. The unit only labels what you type; nothing is converted. Poisson's ratio is a plain number.
3
Read all six constants and the check. The six boxes show E, G, K, nu, lambda and M. The validity box confirms that K and G are positive. The table lists the moduli in several units and the chart shows the trend with Poisson's ratio.

💡 Example Calculations

Example 1 — Steel from E and Poisson's Ratio

E = 200 GPa, ν = 0.30 (illustrative steel)

1
G = 200 / (2 × 1.3) = 76.923 GPa and K = 200 / (3 × 0.4) = 166.67 GPa
2
λ = K − 2G/3 = 166.67 − 51.28 = 115.38 GPa
3
M = K + 4G/3 = 166.67 + 102.56 = 269.23 GPa. Both K and G are positive, so the set is valid.
G = 76.923 GPa, K = 166.67 GPa, λ = 115.38 GPa, M = 269.23 GPa
Try this example →

Example 2 — From Shear and Bulk Modulus

G = 26 GPa and K = 76 GPa (aluminium-like)

1
3K + G = 228 + 26 = 254, so E = 9 × 76 × 26 / 254 = 70.016 GPa
2
ν = (3K − 2G) / (2 (3K + G)) = (228 − 52) / 508 = 0.34646
3
λ = 76 − 17.333 = 58.667 GPa and M = 76 + 34.667 = 110.67 GPa
E = 70.016 GPa, ν = 0.34646
Try this example →

Example 3 — From Young's and Shear Modulus

E = 69 GPa and G = 26 GPa

1
K = E G / (3 (3G − E)) = 1794 / (3 × 9) = 66.444 GPa
2
ν = E / (2G) − 1 = 69 / 52 − 1 = 0.32692
3
λ = 66.444 − 17.333 = 49.111 GPa and M = 66.444 + 34.667 = 101.11 GPa
K = 66.444 GPa, ν = 0.32692
Try this example →

Example 4 — From the Lamé Parameters

λ = 100 GPa and G = 80 GPa

1
K = λ + 2G/3 = 100 + 53.333 = 153.33 GPa and M = λ + 2G = 260.00 GPa
2
E = 9 K G / (3K + G) = 9 × 153.33 × 80 / 540 = 204.44 GPa
3
ν = (460 − 160) / (2 × 540) = 0.27778
E = 204.44 GPa, ν = 0.27778
Try this example →

Example 5 — Young's and P-wave Modulus (Two Roots)

E = 100 GPa and M = 135 GPa

1
S = √(E² + 9M² − 10EM) = √(10000 + 164025 − 135000) = 197.5
2
K = (3M − E + S) / 6 = 83.758 GPa and G = (3M + E − S) / 8 = 38.432 GPa
3
ν = 0.30101 and λ = 58.137 GPa. The other root (minus S) gives ν = −0.4306 and G = 87.818 GPa; this calculator reports the one with ν of zero or more and mentions the other in the note.
G = 38.432 GPa, K = 83.758 GPa, ν = 0.30101
Try this example →

Example 6 — US Units (ksi)

E = 29000 ksi and ν = 0.30 (illustrative structural steel)

1
G = 29000 / 2.6 = 11154 ksi and K = 29000 / 1.2 = 24167 ksi
2
λ = 24167 − 7436 = 16731 ksi and M = 24167 + 14872 = 39038 ksi
3
In SI this is E = 199.95 GPa, close to the 200 GPa of Example 1; the table converts every constant to GPa, MPa and psi.
G = 11154 ksi, K = 24167 ksi
Try this example →

❓ Frequently Asked Questions

How many elastic constants does an isotropic material have?+
Only two are independent. Young's modulus E, shear modulus G, bulk modulus K, Poisson's ratio nu, Lame's first parameter lambda and the P-wave modulus M are all interchangeable once any two are known. Anisotropic materials need more.
How do you convert E and nu to G and K?+
G = E / (2 (1 + nu)) and K = E / (3 (1 - 2 nu)). For E = 200 GPa and nu = 0.30, G = 76.92 GPa and K = 166.67 GPa. Lambda and M follow from lambda = K - 2G/3 and M = K + 4G/3.
How do you calculate Young's modulus from K and G?+
E = 9 K G / (3 K + G). With K = 76 GPa and G = 26 GPa, E = 17784 / 254 = 70.02 GPa. Poisson's ratio is nu = (3K - 2G) / (2 (3K + G)) = 0.3465.
What is the P-wave modulus M?+
M = lambda + 2G = K + 4G/3 is the longitudinal (constrained) modulus, the stiffness for uniaxial strain with no lateral expansion. The P-wave speed in a solid is the square root of M divided by the density.
What are the Lame parameters?+
Lame's first parameter lambda and the second parameter mu (which equals the shear modulus G) appear in the stress-strain relation sigma = lambda tr(epsilon) I + 2 mu epsilon. They are convenient in wave propagation and tensor formulations of elasticity.
What range can Poisson's ratio have?+
For a stable isotropic solid, -1 < nu < 0.5. These limits come from requiring the shear modulus and the bulk modulus to be positive. The calculator flags any set outside this range as not valid.
Why does the E and M pair sometimes have two answers?+
Solving for K and G from E and M involves a square root, so there are two roots, one with nu of zero or more and one with nu of zero or less. For E = 100 and M = 135 they give nu = 0.301 and nu = -0.431. The calculator reports the first and mentions the second.
Can lambda be negative?+
Yes. lambda = E nu / ((1 + nu)(1 - 2 nu)) is negative whenever nu is negative, as in auxetic materials. It is zero when nu is zero, when K equals two thirds of G.
Which unit should I use for the moduli?+
Use whatever your source uses. The unit selector only labels the numbers, so a value typed as 29000 with ksi stays in ksi, and the table below the results converts to GPa, MPa and psi. Poisson's ratio has no unit.
Do these formulas work for rock, soil or composites?+
They apply to isotropic linear elastic behaviour. Rock and soil are often treated that way for small strain, but layered rock, wood, laminates and crystals are anisotropic and need directional constants.
What does the validity check test?+
It tests that G and K are both positive, the stability conditions for an isotropic solid, which is the same as E being positive and nu lying strictly between -1 and 0.5. A failing result usually means a typo, a unit mix-up or data from an anisotropic material.
How are wave speeds related to these constants?+
The shear wave speed is the square root of G over density and the compressional wave speed is the square root of M over density. For steel with M = 269 GPa and density 7850 kg/m3 this gives about 5.9 km/s.

How many elastic constants does an isotropic material have?

Only two are independent. Young's modulus E, shear modulus G, bulk modulus K, Poisson's ratio nu, Lame's first parameter lambda and the P-wave modulus M are all interchangeable once any two are known.

How do you convert E and nu to G and K?

G = E / (2 (1 + nu)) and K = E / (3 (1 - 2 nu)). For E = 200 GPa and nu = 0.30, G = 76.92 GPa and K = 166.67 GPa. Lambda and M follow from lambda = K - 2G/3 and M = K + 4G/3.

How do you calculate Young's modulus from K and G?

E = 9 K G / (3 K + G). With K = 76 GPa and G = 26 GPa, E = 17784 / 254 = 70.02 GPa. Poisson's ratio is nu = (3K - 2G) / (2 (3K + G)) = 0.3465.

What is the P-wave modulus M?

M = lambda + 2G = K + 4G/3 is the longitudinal (constrained) modulus, the stiffness for uniaxial strain with no lateral expansion. The P-wave speed in a solid is the square root of M divided by density.

What are Lame parameters?

Lame's first parameter lambda and the second parameter mu (which equals the shear modulus G) are the two constants used in the stress-strain relation sigma = lambda tr(epsilon) I + 2 mu epsilon. They are convenient in wave and tensor formulations.

What range can Poisson's ratio have?

For a stable isotropic solid, -1 < nu < 0.5. These limits come from requiring the shear modulus and bulk modulus to be positive. The calculator flags any set outside this range as not valid.

Why does the E and M pair sometimes have two answers?

Solving for K and G from E and M involves a square root, so there are two roots, one with nu of zero or more and one with nu of zero or less. For E = 100 and M = 135 they give nu = 0.301 and nu = -0.431. The calculator reports the first.

Can lambda be negative?

Yes. lambda = E nu / ((1 + nu)(1 - 2 nu)) is negative whenever nu is negative, which happens for auxetic materials. It is zero when nu is zero.