Distance Attenuation Calculator

See how a sound level, a light or a radio signal falls with distance under the inverse-square law, and how far away a target level is.

📉 Distance Attenuation Calculator
Known level (L1)
dB
At distance (r1)
m
New distance (r2)
m
Source type
Air absorption preset (illustrative)
Air absorption (α)
dB/m
Known level (L1)
dB
At distance (r1)
m
Target level (L2)
dB
Source type
Air absorption preset (illustrative)
Air absorption (α)
dB/m
Intensity at the first distance (I1), any unit
First distance (r1)
Second distance (r2)
Source type
Level at new distance
—
Change in level
—
From spreading
—
From air absorption
—
Pressure ratio p2/p1
—
Intensity ratio I2/I1
—
Change per doubling
—
Distance ratio r2/r1
—

Distance for target level
—
In metres
—
In feet
—
Distance ratio r2/r1
—
Without air absorption
—
Spreading loss
—
Absorption loss
—
Total drop L1 − L2
—

Intensity at second distance
—
Fraction remaining
—
Reduction factor
—
Change in dB
—
Field amplitude ratio
—
Distance ratio r2/r1
—

📉 What is Distance Attenuation?

Distance attenuation is the weakening of a wave as it moves away from its source. The simplest and most important part of it is geometric spreading: the energy leaving a small source spreads over a sphere whose area grows as 4πr², so the intensity falls as 1/r². This is the inverse-square law. In decibels it means the level drops by 20 log10(r2/r1) between two distances, which is 6.02 dB every time the distance doubles and 20 dB every time it grows tenfold.

The law is used everywhere waves travel outward. Acousticians use it to predict how loud a speaker, a machine or a siren will be at a fence line or a neighbour's window, and to check workplace noise limits. Photographers and lighting designers use it to estimate how much light reaches a subject when a lamp moves back. Radio engineers use it as the free-space part of a link budget, and radiation safety staff use it to estimate how quickly a point source fades with distance. A second step is often added for sound: air absorption, which removes a further number of decibels per metre, especially at high frequency.

The geometry matters. A small compact source (a speaker, a person talking, a lamp) behaves as a point source with a 6 dB drop per doubling. A long, steady line of sources, such as a busy road or a pipeline, spreads the energy over a cylinder instead, so the intensity falls as 1/r and the level drops about 3 dB per doubling. The simple law also assumes free field, meaning no walls, ground reflections, barriers or wind effects. Inside a room the reverberant sound makes levels fall more slowly than the law predicts, and very close to a large source the near-field behaviour is different. Ocean acoustics adds absorption and refraction, covered in the sonar range equation calculator, and radio links use the Friis transmission equation.

This calculator has three modes. Level at a distance gives the new level, with the spreading and absorption contributions shown separately. Find distance solves the opposite problem, the distance at which a level falls to a target. Inverse-square intensity works in plain linear units for light, radio power density or sound intensity. Each has a chart that marks your numbers.

📐 Formula

L2  =  L1 − 20 log10( r2 / r1 ) − α ( r2 − r1 )
L1, L2 = sound levels (dB) at distances r1 and r2
r1, r2 = distances from the source (m)
α = air absorption coefficient (dB per metre), 0 to ignore absorption
Line source: replace 20 log10 with 10 log10, a drop of 3.01 dB per doubling
Distance for a target level (no absorption): r2 = r1 × 10(L1 − L2)/20. With absorption it is solved numerically.
Intensity form: I2 = I1 ( r1 / r2 )² for a point source, or I1 ( r1 / r2 ) for a line source
Example: 94 dB at 1 m becomes 94 − 20 log10(8) = 75.94 dB at 8 m

📖 How to Use This Calculator

Steps

1
Choose a mode. Level at a distance finds the level at a new distance, Find distance finds where a target level occurs, and Inverse-square intensity handles light, radio or any linear intensity.
2
Enter what you know. Type the known level and its distance, then the new distance or target level. Pick a point source or a line source, and set an air absorption in dB per metre if you want it included. The presets are only rough illustrative values.
3
Read the result and the chart. The result shows the answer and how much of the change comes from spreading and from absorption. The chart plots level against distance on a log axis, or intensity against distance, with your points marked.

💡 Example Calculations

Example 1 — Loudspeaker at 8 Metres

A speaker measures 94 dB at 1 m. Point source, no absorption. What is the level at 8 m?

1
Distance ratio r2/r1 = 8 / 1 = 8.000
2
Spreading loss = 20 log10(8) = 18.06 dB
3
L2 = 94 − 18.06 = 75.94 dB. The pressure is 0.1250 of the original and the intensity ratio is 0.0156.
Level at 8 m = 75.94 dB (change of −18.06 dB)
Try this example →

Example 2 — Busy Road as a Line Source

Traffic gives 70 dB at 15 m. Line source, no absorption. What is the level at 60 m?

1
Distance ratio = 60 / 15 = 4.000
2
Spreading loss = 10 log10(4) = 6.02 dB, only half of the 12.04 dB a point source would give
3
L2 = 70 − 6.02 = 63.98 dB. A real road also has ground effects and barriers that this simple model leaves out.
Level at 60 m = 63.98 dB (3.01 dB per doubling)
Try this example →

Example 3 — Long Range with Air Absorption

100 dB at 1 m, point source, 200 m away, with an assumed absorption of 0.08 dB/m (illustrative high-frequency value)

1
Spreading loss = 20 log10(200) = 46.02 dB
2
Absorption loss = 0.08 × (200 − 1) = 15.92 dB
3
L2 = 100 − 46.02 − 15.92 = 38.06 dB, a total change of −61.94 dB
Level at 200 m = 38.06 dB (spreading 46.02 dB, absorption 15.92 dB)
Try this example →

Example 4 — Where Does 100 dB Become 60 dB?

100 dB at 1 m, target 60 dB, point source, no absorption

1
Required drop = 100 − 60 = 40 dB
2
r2 = 1 × 1040/20 = 1 × 102 = 100 m
3
That is 328.1 ft, and the distance ratio is 100.000 because 40 dB is two factors of 10 at 20 dB each.
Distance = 100.00 m (328.1 ft)
Try this example →

Example 5 — The Same Target with Air Absorption

100 dB at 1 m, target 60 dB, point source, assumed absorption 0.02 dB/m (illustrative)

1
Solve 100 − 20 log10(r) − 0.02 (r − 1) = 60 numerically, which gives r = 82.83 m
2
Check: spreading 20 log10(82.83) = 38.36 dB and absorption 0.02 × 81.83 = 1.64 dB, total 40.00 dB
3
Without absorption the target sits at 100.00 m, so absorption pulls it in by 17.2 percent.
Distance = 82.83 m (100.00 m without absorption)
Try this example →

Example 6 — A Lamp Moved Back from 1 m to 4 m

A lamp gives 800 lux at 1 m. Point source. What does a surface 4 m away receive?

1
Distance ratio = 4 / 1 = 4.000, so the fraction remaining is (1/4)² = 0.0625
2
I2 = 800 × 0.0625 = 50.000 lux, a reduction by a factor of 16
3
In decibels that is 10 log10(0.0625) = −12.04 dB, and the field amplitude ratio is 0.2500.
Illuminance at 4 m = 50.000 lux (−12.04 dB)
Try this example →

❓ Frequently Asked Questions

What is the inverse-square law for sound?+
For a small source in open space the sound intensity falls in proportion to 1/r squared, because the same power spreads over a sphere of area 4 pi r squared. The sound pressure level therefore drops by 20 log10(r2/r1) decibels.
How many dB does sound drop when you double the distance?+
About 6.02 dB for a point source in free field (20 log10 of 2). The figure is usually rounded to 6 dB. For a line source such as a long road it is about 3.01 dB per doubling.
What is the formula for sound level at a distance?+
L2 = L1 - 20 log10(r2/r1) for a point source. For a line source use 10 log10(r2/r1). Subtract an extra alpha times (r2 - r1) decibels if you include air absorption of alpha dB per metre.
How far does sound travel before it falls to a given level?+
Rearrange the formula: r2 = r1 times 10 raised to (L1 - L2)/20 for a point source. A level of 100 dB at 1 m falls to 60 dB at 100 m with no absorption, because 40 dB is a factor of 100 in distance.
Is the inverse-square law the same for sound pressure and intensity?+
Intensity falls as 1/r squared and pressure amplitude falls as 1/r. Both correspond to the same decibel change, 20 log10 of the distance ratio, which is why the rule is quoted as 6 dB per doubling for both.
What is the difference between a point source and a line source?+
A point source spreads its power over a sphere, intensity falls as 1/r squared and the level drops 6 dB per doubling. A long line source such as steady road traffic spreads over a cylinder, intensity falls as 1/r and the level drops 3 dB per doubling.
Does air absorb sound?+
Yes, mostly high frequencies. The loss depends on frequency, temperature and humidity and is specified in ISO 9613-1. The presets here are only rough illustrative values, so enter your own dB per metre for real work.
Does the inverse-square law apply to light and radio?+
Yes, for a small source in free space. The illuminance in lux or the power density in W/m2 falls as 1/r squared, so doubling the distance leaves a quarter of the value. Use the Inverse-square intensity mode for these.
Why does my measured level fall more slowly than predicted?+
Reflections from walls, floors and ceilings add reverberant sound, so indoor levels do not follow the free-field rule. Wind, temperature gradients and ground effects also change outdoor levels at long range.
What reference distance should I use?+
Use the distance at which the level was measured or specified, often 1 m for loudspeakers and 10 m or 15 m for traffic and machinery. The law needs the source to be small compared with that distance.
Can the level go up when I move closer?+
Yes, in the model. A shorter distance gives a negative spreading loss, which raises the level. The model breaks down very close to a real source, in the near field, where the source size matters.
How do I add several sources?+
Calculate each level at your location, convert each to intensity with 10 to the power L/10, add the intensities and convert back with 10 log10. Two equal sources raise the level by 3.01 dB, which this calculator does not do for you.

What is the inverse-square law for sound?

For a small source in open space the sound intensity falls in proportion to 1/r squared, because the same power spreads over a sphere of area 4 pi r squared. The sound pressure level therefore drops by 20 log10(r2/r1) decibels.

How many dB does sound drop when you double the distance?

About 6.02 dB for a point source in free field (20 log10 of 2). The figure is usually rounded to 6 dB. For a line source such as a long road it is about 3.01 dB per doubling.

What is the formula for sound level at a distance?

L2 = L1 - 20 log10(r2/r1) for a point source. For a line source use 10 log10(r2/r1). Subtract an extra alpha times (r2 - r1) decibels if you include air absorption of alpha dB per metre.

How far does sound travel before it falls to a given level?

Rearrange the formula: r2 = r1 times 10 raised to (L1 - L2)/20 for a point source. A level of 100 dB at 1 m falls to 60 dB at 100 m with no absorption, because 40 dB is a factor of 100 in distance.

Is the inverse-square law the same for sound pressure and intensity?

Intensity falls as 1/r squared and pressure amplitude falls as 1/r. Both correspond to the same decibel change, 20 log10 of the distance ratio, which is why the rule is quoted as 6 dB per doubling for both.

What is the difference between a point source and a line source?

A point source spreads its power over a sphere, intensity falls as 1/r squared and the level drops 6 dB per doubling. A long line source such as steady road traffic spreads over a cylinder, intensity falls as 1/r and the level drops 3 dB per doubling.

Does air absorb sound?

Yes, mostly high frequencies. The loss depends on frequency, temperature and humidity and is specified in ISO 9613-1. The presets here are only rough illustrative values and you should enter your own dB per metre for real work.

Does the inverse-square law apply to light and radio?

Yes, for a small source in free space. The illuminance in lux or the power density in W/m2 falls as 1/r squared, so doubling the distance leaves a quarter of the value. Use the Inverse-square intensity mode for these.

Why does my measured level fall more slowly than predicted?

Reflections from walls, floors and ceilings add reverberant sound, so indoor levels do not follow the free-field rule. Wind, temperature gradients and ground effects also change outdoor levels at long range.

What reference distance should I use?

Use the distance at which the level was measured or specified, often 1 m for loudspeakers and 10 m or 15 m for traffic and machinery. The law needs the source to be small compared with that distance.

Can the level go up when I move closer?

Yes, in the model. A shorter distance gives a negative spreading loss, which raises the level. The model breaks down very close to a real source, in the near field, where the source size matters.