Crawl Ratio Calculator

Multiply your gear ratios to get the crawl ratio, then see how slowly you can creep, how much torque reaches the wheels and what bigger tires do.

🚙 Crawl Ratio Calculator
First gear ratio
: 1
110
Transfer case low
: 1
16
Axle ratio
: 1
28
Engine speed
rpm
Tire diameter
in
2545
Engine torque
N·m
Drivetrain efficiency
%
Stock tire (width / aspect R wheel)
mm
%
in
New tire (width / aspect R wheel)
mm
%
in
Crawl ratio
—
Use band (illustrative)
—
Crawl speed (mph)
—
Crawl speed (km/h)
—
Wheel torque (N·m)
—
Wheel torque (lb-ft)
—
Tractive force at tire
—
Torque multiplication
—
Engine revolutions
—
Effective ratio, new tire
—
Crawl ratio (gears)
—
Stock diameter
—
New diameter
—
Diameter change
—
Speed, stock tire
—
Speed, new tire
—
Axle ratio to restore
—

🚙 What is Crawl Ratio?

Crawl ratio is the lowest overall gear ratio a vehicle's drivetrain can reach, found by multiplying the first gear ratio of the transmission, the low range ratio of the transfer case and the ratio of the axle. It tells you how many times the engine turns for each turn of the wheels in the lowest gear. A high crawl ratio means the vehicle can move very slowly even with the engine well above idle, and that the engine's torque is multiplied strongly on its way to the wheels. It is most often discussed for four-wheel-drive vehicles used in technical off-road driving, such as rock crawling, but the same multiplication applies to any drive layout.

The number matters in practice. A high ratio lets a driver pick a path over boulders or steep ledges at walking pace, with precise throttle control and without needing the clutch or brake constantly. It also helps with towing from a standstill, pulling a stuck vehicle out and descending steep terrain with engine braking. When people change tire size, add a lift or swap axles, they use crawl ratio to judge how the vehicle will behave and to decide whether to re-gear. Wheel torque and speed at a given engine rpm follow directly from the overall ratio and the tire diameter.

Several points are easy to get wrong. Crawl ratio is a gearing number, not a measure of capability, because grip, ground clearance, suspension and engine low-speed torque still decide what a vehicle can climb. Tire size does not change the ratio itself, but taller tires reduce the effective ratio at the ground, so this page compares tires separately. Typical "good" ranges quoted online are opinions that vary by source, so the bands shown here are illustrative. And it is not the same as a plain gearbox calculation, for which the gear ratio calculator is the right page.

This calculator gives the crawl ratio, the road speed at your chosen engine speed, the wheel torque and tractive force from your engine torque, and the number of engine revolutions per mile. A second mode compares two metric tire sizes and shows the new effective ratio and the axle ratio that would restore the original feel.

📐 Formula

Crawl ratio  =  R1st × RTC × Raxle
R1st = first gear ratio of the transmission
RTC = transfer case low range ratio (use 1 if there is no low range)
Raxle = axle (final drive) ratio
Road speed: v (mph) = rpm × π × Dtire (in) × 60 / (ratio × 12 × 5280)
Wheel torque: Twheel = Tengine × ratio × efficiency, and tractive force F = Twheel / tire radius
Tire diameter from metric size: D (in) = wheel diameter + 2 × width (mm) × aspect (%) / 100 / 25.4
Effective ratio with a new tire: ratio × Dstock / Dnew, and the axle ratio that restores it is axle × Dnew / Dstock
Example: 5.13 × 4.01 × 4.10 = 84.34 : 1

📖 How to Use This Calculator

Steps

1
Enter the gear ratios. Type the first gear, transfer case low and axle ratios, and the engine rpm at which you want the road speed.
2
Add tire and torque data. In Crawl ratio mode enter the tire diameter, engine torque and drivetrain efficiency. In Tire size effect mode enter the width, aspect ratio and wheel diameter of the stock and new tires.
3
Read the results. See the crawl ratio, crawl speed, wheel torque and the illustrative band, or the change in effective ratio and the axle ratio that restores the original. The chart marks your values.

💡 Example Calculations

Example 1 — Published Rubicon-Style Gearing

1st gear 5.13, transfer case low 4.01, axle 4.10, 33 inch tires, 1000 rpm, 350 N·m, 90 percent efficiency

1
Crawl ratio = 5.13 × 4.01 × 4.10 = 84.34 : 1, which matches the worked example given in the Wikipedia article on crawl ratio.
2
Speed = 1000 × π × 33 × 60 / (84.34 × 12 × 5280) = 1.164 mph (1.873 km/h)
3
Wheel torque = 350 × 84.34 × 0.90 = 26568 N·m (19595 lb-ft), a tractive force of 63393 N at the 0.4191 m tire radius.
Crawl ratio = 84.34 : 1, crawl speed = 1.164 mph
Try this example →

Example 2 — Typical Trail Truck

1st gear 4.46, transfer case low 2.72, axle 4.10, 33 inch tires, 1000 rpm

1
Crawl ratio = 4.46 × 2.72 × 4.10 = 49.74 : 1
2
Speed at 1000 rpm = 1.974 mph (3.177 km/h), roughly 70 percent faster than Example 1.
3
Wheel torque = 350 × 49.74 × 0.90 = 15667 N·m, a torque multiplication of 44.76 times. The illustrative band for this ratio is mild trail use.
Crawl ratio = 49.74 : 1, crawl speed = 1.974 mph
Try this example →

Example 3 — Same Truck on 35 Inch Tires

Same gearing as Example 2 with a 35 inch tire

1
The crawl ratio is unchanged at 49.74 : 1 because it depends only on the gears.
2
Speed = 1000 × π × 35 × 60 / (49.74 × 12 × 5280) = 2.093 mph, up 6.1 percent from the 33 inch tire.
3
Wheel torque is the same 15667 N·m, but the larger 0.4445 m tire radius lowers the tractive force at the ground from 37384 N to 35247 N.
Crawl speed = 2.093 mph, tractive force = 35247 N
Try this example →

Example 4 — Re-gearing the Axles

Same truck with a 5.13 axle, 33 inch tires, 1200 rpm

1
Crawl ratio = 4.46 × 2.72 × 5.13 = 62.23 : 1, up 25 percent from 49.74 because 5.13 / 4.10 = 1.251.
2
Speed at 1200 rpm = 1.893 mph (3.047 km/h)
3
Wheel torque = 350 × 62.23 × 0.90 = 19603 N·m and the engine makes 38034 revolutions per mile.
Crawl ratio = 62.23 : 1, crawl speed = 1.893 mph
Try this example →

Example 5 — Stock 255/75R17 to 285/75R17

Gearing 4.46 × 2.72 × 4.10, 1000 rpm

1
Stock diameter = 17 + 2 × 255 × 0.75 / 25.4 = 32.06 in. New diameter = 17 + 2 × 285 × 0.75 / 25.4 = 33.83 in (+5.53 percent).
2
Speed at 1000 rpm rises from 1.918 mph to 2.024 mph.
3
Effective ratio = 49.74 × 32.06 / 33.83 = 47.13 : 1. An axle ratio of 4.10 × 33.83 / 32.06 = 4.327 would restore the stock feel.
Effective ratio = 47.13 : 1, restoring axle ratio = 4.327
Try this example →

Example 6 — Stock 255/75R17 to 305/70R17

Gearing 5.13 × 4.01 × 4.10, 1000 rpm

1
New diameter = 17 + 2 × 305 × 0.70 / 25.4 = 33.81 in, 5.46 percent taller than 32.06 in.
2
Speed rises from 1.131 mph to 1.193 mph at the same 84.34 ratio.
3
Effective ratio = 84.34 × 32.06 / 33.81 = 79.97 : 1, with a restoring axle ratio of 4.324.
Effective ratio = 79.97 : 1
Try this example →

❓ Frequently Asked Questions

What is the crawl ratio formula?+
Crawl ratio equals the first gear ratio times the transfer case low range ratio times the axle ratio. For example 5.13 x 4.01 x 4.10 = 84.34 to 1. If the vehicle has no transfer case low range, use 1 for that term and the result is the overall first gear ratio.
What is a good crawl ratio?+
It depends on the use. Road-oriented vehicles are well under 50, trail vehicles are often quoted between about 50 and 100, and dedicated rock crawlers go higher. These bands are rough rules of thumb that differ between sources, so treat them as illustrative and think about your terrain and tires.
Does tire size change the crawl ratio?+
The crawl ratio itself, as a product of gear ratios, does not change. But taller tires cover more ground per revolution, so the effective ratio at the ground falls in proportion to the tire diameter and the crawl speed rises. Tire size mode shows the effective ratio.
How do I calculate crawl speed?+
Speed in mph = engine rpm x pi x tire diameter in inches x 60 / (ratio x 12 x 5280). With 33 inch tires, an 84.34 ratio and 1000 rpm this gives 1.16 mph. The calculator also gives km/h and the engine revolutions needed per mile.
How much torque reaches the wheels?+
Wheel torque is engine torque times the overall ratio times drivetrain efficiency. The efficiency of 85 to 95 percent is a typical illustrative range. The result is the combined torque at all driven wheels, not per wheel, and it ignores tire slip.
Is a higher crawl ratio always better?+
No. A higher ratio gives slower speeds and more wheel torque, but it also makes a vehicle slower on the highway if the axle ratio is raised, and it does nothing for grip. Beyond a point the gains are small, and the engine may need to spin fast just to move.
How do I find my transfer case low ratio?+
Look it up in the owner's manual or the manufacturer's specifications for your model and year, since several ratios exist, such as 2.72 or 4.01. Aftermarket gear sets can also change it. Enter the ratio exactly as published for the best result.
How is this different from a gear ratio calculator?+
A gear ratio calculator handles a single pair of gears. The crawl ratio multiplies three stages and goes further, turning the product into road speed at a given rpm, torque at the wheels and the effect of tire diameter. It is aimed at vehicles, not general gear trains.
How is tire diameter found from a metric tire size?+
The diameter is the wheel diameter plus twice the sidewall height. The sidewall height is the width times the aspect ratio percentage. For a 285/75R17 the sidewall is 285 x 0.75 = 213.75 mm, so the diameter is 17 + 2 x 213.75 / 25.4 = 33.83 inches.
How do I restore my gearing after fitting bigger tires?+
Multiply the axle ratio by the new tire diameter divided by the old one. For a 5.5 percent taller tire a 4.10 axle becomes about 4.33. Axles are sold in discrete ratios, so pick the closest one, and check that the transmission and transfer case can handle the changes.
Why does the calculator show engine revolutions per mile?+
It is a direct way to see how much gearing there is. Engine revolutions per mile equal the overall ratio times the tire revolutions per mile. A tall ratio such as 84 : 1 on 33 inch tires needs about 51,500 engine revolutions to cover a mile.

What is the crawl ratio formula?

Crawl ratio equals the first gear ratio times the transfer case low range ratio times the axle ratio. For example 5.13 x 4.01 x 4.10 = 84.34 to 1.

What is a good crawl ratio?

It depends on use. Road-oriented vehicles are well below 50, trail vehicles are often quoted between about 50 and 100, and dedicated rock crawlers go higher. These bands are rough rules of thumb that vary between sources.

How does tire size affect crawl ratio?

The crawl ratio itself is the product of gear ratios and does not change with tires. But taller tires cover more ground per revolution, so the effective ratio at the ground falls in proportion to the tire diameter, and the crawl speed rises.

How do I calculate crawl speed?

Speed in mph = engine rpm x pi x tire diameter in inches x 60 / (ratio x 12 x 5280). At 1000 rpm with 33 inch tires and an 84.34 ratio this gives 1.16 mph.

How much torque reaches the wheels at crawl ratio?

Wheel torque is engine torque times the overall ratio times drivetrain efficiency. Efficiency is often around 85 to 95 percent, an illustrative range, so a 350 N m engine at an 84.34 ratio and 90 percent efficiency gives about 26,568 N m at the wheels combined.

Does tire size change the crawl ratio?

The crawl ratio itself, as a product of gear ratios, does not change. But taller tires cover more ground per revolution, so the effective ratio at the ground falls in proportion to the tire diameter and the crawl speed rises. Tire size mode shows the effective ratio.

How much torque reaches the wheels?

Wheel torque is engine torque times the overall ratio times drivetrain efficiency. The efficiency of 85 to 95 percent is a typical illustrative range. The result is the combined torque at all driven wheels, not per wheel, and it ignores tire slip.

Is a higher crawl ratio always better?

No. A higher ratio gives slower speeds and more wheel torque, but it also makes a vehicle slower on the highway if the axle ratio is raised, and it does nothing for grip. Beyond a point the gains are small, and the engine may need to spin fast just to move.

How do I find my transfer case low ratio?

Look it up in the owner's manual or the manufacturer's specifications for your model and year, since several ratios exist, such as 2.72 or 4.01. Aftermarket gear sets can also change it. Enter the ratio exactly as published for the best result.