Bulk Modulus Calculator

Measure how stiff a material is against squeezing, predict its volume change under pressure, and link K to sound speed and to Young's modulus.

🧊 Bulk Modulus Calculator
Volumes before and afterany one unit, such as mL
Initial volume V0
Final volume V1
Pressure change ΔPpositive when the pressure rises
Material preset (illustrative)
Bulk modulus K
Pressure change ΔPnegative for a pressure drop
Initial volume V0any one unit
Fluid preset (illustrative)
Bulk modulus K (adiabatic)
Density
kg/m³
Material preset (illustrative)
Known modulus
Poisson's ratio νbetween -1 and 0.5, most metals 0.25 to 0.35
Bulk modulus K
—
Compressibility 1 / K
—
Volumetric strain
—
Volume change
—
Density change
—
Pressure change
—
Closest preset
—

Volume change
—
Final volume
—
Volumetric strain
—
Density change
—
Bulk modulus used
—
Pressure change
—
Compressibility 1 / K
—

Speed of sound c
—
In km/h
—
Travel time
—
Bulk modulus used
—
Density used
—
Acoustic impedance ρc
—
Compared with air
—

Bulk modulus K
—
Young's modulus E
—
Shear modulus G
—
Lamé first parameter
—
P-wave modulus K + 4G/3
—
Poisson's ratio
—
Ratio K / E
—
Compressibility 1 / K
—

🧊 What is the Bulk Modulus?

The bulk modulus K measures how strongly a material resists being squeezed from all sides. It is defined as the pressure increase needed to cause a given relative decrease in volume: K = −V dP/dV. A large K means the material is hard to compress, a small K means it gives way easily. It has the units of pressure, pascals, and it is quoted in GPa for solids and liquids and in kPa or MPa for gases. Its reciprocal, 1/K, is the compressibility, the fractional volume shrinkage per unit of pressure.

Engineers and scientists use the bulk modulus in many places. Hydraulic designers use it to estimate how much oil compresses in a stiff-looking system, which sets its natural frequency and response. Oceanographers and acousticians need it for the speed of sound, because a wave in a fluid travels at the square root of K divided by density. Geophysicists use the bulk modulus of rock and water when interpreting seismic velocities, and materials scientists relate it to the other elastic constants. It is also what makes a deep-sea water column slightly denser at depth, and it is why air in a syringe compresses easily while water in the same syringe barely moves.

Two cautions are important. First, K is not always a single number. For a gas the modulus depends on how it is compressed: slowly, with heat flowing out, it equals the pressure (isothermal), and quickly, as in a sound wave, it is gamma times the pressure (adiabatic). Liquids and solids also show a modulus that rises with pressure and falls with temperature, so a measured change over a large pressure range gives a secant average. Second, K is only one of several elastic moduli. For an isotropic solid it is tied to Young's modulus E and Poisson's ratio ν by K = E / (3 (1 − 2ν)), which this page also solves. The presets here are illustrative values to get you started, not data for a specific sample.

This page differs from its neighbours. The sound speed in fluid calculator centres on the speed of sound in gases and liquids, and the speed of sound in solids calculator centres on wave speeds from E, ν and density. Here the focus is the modulus itself: finding K from a measured compression, predicting the volume change under a pressure, and converting to and from the other elastic constants. For stiffness in tension see the stress-strain calculator.

📐 Formula

K = −V0 ΔP / ΔV    β = 1 / K    c = √(K / ρ)    K = E / (3 (1 − 2ν))
K = bulk modulus in Pa. V0 = initial volume, ΔV = V1 − V0 the volume change (negative when the pressure rises) and ΔP = the pressure change in Pa.
Volumetric strain: ΔV / V0 = −ΔP / K. The density changes by a factor 1 / (1 + ΔV / V0).
β = compressibility in 1/Pa, the reciprocal of K.
c = speed of sound in a fluid in m/s, with ρ the density in kg/m3. Use the adiabatic K.
Elastic constants: K = E / (3 (1 − 2ν)), G = E / (2 (1 + ν)), λ = E ν / ((1 + ν)(1 − 2ν)) and M = K + 4G/3, for an isotropic linear elastic solid.
Ideal gas: K = P (isothermal) or K = γ P (adiabatic).
Example: V0 = 1000, V1 = 990 and ΔP = 22 MPa give K = 1000 × 22 / 10 = 2200 MPa = 2.2 GPa.

📖 How to Use This Calculator

Steps

1
Choose a mode. Use Find K for a measured compression, Volume change to squeeze a material of known K, Speed of sound for a fluid, or From E and Poisson to convert elastic constants.
2
Enter the values. Type the volumes, pressure change, modulus or density and pick the unit in each dropdown. The unit only sets how your number is read. An illustrative preset can fill common materials.
3
Check the signs. A pressure rise should shrink the volume. If the signs disagree the calculator shows a message instead of a negative modulus.
4
Read the results. The modulus, compressibility, strain, density change, sound speed or related moduli appear with a chart for the chosen mode.

💡 Example Calculations

Example 1 — Measuring the Bulk Modulus of Water

1000 mL of water shrinks to 990 mL when the pressure rises by 22 MPa

1
ΔV = 990 − 1000 = −10 mL, so the strain is −10 / 1000 = −1.000 %.
2
K = −1000 × 22 MPa / (−10) = 2200 MPa = 2.200 GPa.
3
Compressibility = 1 / K = 4.545e-10 per Pa (0.4545 per GPa), and the density rises by 1.010 %.
K = 2.200 GPa, close to the water preset
Try this example →

Example 2 — Water at 100 MPa

1 m³ of water is taken to a pressure 100 MPa higher, roughly 10 km down (K = 2.2 GPa, illustrative)

1
Strain = −ΔP / K = −100 MPa / 2200 MPa = −4.545 %.
2
ΔV = −0.04545 m³ and V1 = 1 × (1 − 0.04545) = 0.954545 m³.
3
The density rises by 1 / 0.954545 − 1 = 4.762 %. In reality K grows with pressure, so the true shrinkage is somewhat smaller.
Volume change = −0.04545 m³, final volume = 0.954545 m³
Try this example →

Example 3 — A Steel Block Under Pressure

1000 cm³ of steel (K = 160 GPa, illustrative) in a 100 MPa pressure chamber

1
Strain = −100 MPa / 160,000 MPa = −0.06250 %.
2
ΔV = 1000 × (−0.000625) = −0.6250 cm³.
3
V1 = 999.375 cm³, compared with a 4.5 % change for the same pressure on water.
Volume change = −0.6250 cm³, final volume = 999.375 cm³
Try this example →

Example 4 — Speed of Sound in Water

Water with K = 2.2 GPa and a density of 998 kg/m³ (illustrative)

1
K / ρ = 2.2 × 109 / 998 = 2,204,409 m²/s².
2
c = √2,204,409 = 1484.7 m/s, which is 5345.0 km/h.
3
Sound covers 1 km in 1000 / 1484.7 = 0.6735 s, about 4.3 times faster than in air.
Speed of sound = 1484.7 m/s
Try this example →

Example 5 — Speed of Sound in Air

Air treated as an ideal gas with the adiabatic modulus K = 1.4 × 101.325 kPa = 141.855 kPa and a density of 1.204 kg/m³

1
K / ρ = 141,855 / 1.204 = 117,819 m²/s².
2
c = √117,819 = 343.25 m/s, or 1235.7 km/h.
3
Using the isothermal K = P would give only 290 m/s, which is why sound needs the adiabatic modulus.
Speed of sound = 343.25 m/s
Try this example →

Example 6 — K From Young's Modulus and Poisson's Ratio

Steel with E = 200 GPa and ν = 0.30 (illustrative)

1
K = E / (3 (1 − 2 × 0.3)) = 200 / (3 × 0.4) = 166.7 GPa.
2
G = 200 / (2 × 1.3) = 76.92 GPa and λ = 200 × 0.3 / (1.3 × 0.4) = 115.4 GPa.
3
P-wave modulus M = K + 4G/3 = 166.7 + 102.6 = 269.2 GPa, and K / E = 0.833.
K = 166.7 GPa, G = 76.92 GPa
Try this example →

❓ Frequently Asked Questions

What is the bulk modulus formula?+
K = -V dP/dV, or for a finite change K = -V0 x ΔP / ΔV. Compressing 1000 mL of water to 990 mL needs about 22 MPa, so K is 1000 x 22 / 10 = 2200 MPa, or 2.2 GPa.
What are the units of bulk modulus?+
Pascals, the same as pressure, usually quoted in GPa for solids and liquids and in kPa for gases. 1 GPa is 1,000,000,000 Pa, about 145,038 psi.
What is compressibility?+
Compressibility is the reciprocal of the bulk modulus, β = 1 / K. Water at 2.2 GPa has β of about 4.5e-10 per Pa, or 0.45 per GPa, meaning a 1 GPa pressure rise would cut the volume by about 45 percent if K stayed constant.
How do you find the speed of sound from the bulk modulus?+
c = square root of K over ρ. Water with K = 2.2 GPa and ρ = 998 kg/m3 gives 1484.7 m/s. Use the adiabatic modulus, because sound compresses the fluid too quickly for heat to flow.
How is bulk modulus related to Young's modulus?+
K = E / (3 (1 - 2ν)) for an isotropic elastic solid. Steel with E = 200 GPa and ν = 0.30 gives K = 166.7 GPa. When ν = 1/3, K equals E.
Why is the bulk modulus of a gas equal to its pressure?+
For an ideal gas compressed isothermally, PV is constant, so dP/dV = -P/V and K = P. For adiabatic compression K = γP, which is 1.4 times the pressure for air. At one atmosphere that is about 101.3 kPa isothermal and 141.9 kPa adiabatic.
What is a high bulk modulus?+
A high modulus means a material that is hard to compress. Steel is around 160 GPa, water 2.2 GPa and air only about 0.1 MPa. Liquids are nearly incompressible compared with gases but still compress measurably in the deep ocean.
How much does water compress at the bottom of the ocean?+
At about 100 MPa, roughly the pressure near 10 km depth, a constant K of 2.2 GPa gives a volume drop of 4.5 percent and a density rise of 4.8 percent. K itself rises with pressure, so the true change is somewhat smaller.
Can the bulk modulus be negative?+
Not for a stable material, because a pressure increase must shrink it. A negative result from measured data means the pressure and volume changes have inconsistent signs or the measurement is wrong.
What is the difference between isothermal and adiabatic bulk modulus?+
The isothermal value applies when temperature is held constant and the adiabatic (isentropic) one when no heat flows. The adiabatic modulus is larger, and it is the right one for sound waves.
Why does Poisson's ratio of 0.5 give an infinite bulk modulus?+
In K = E / (3 (1 - 2ν)) the denominator goes to zero as ν approaches 0.5, which describes a perfectly incompressible material. Rubber with ν near 0.49 has a bulk modulus far larger than its Young's modulus.

What is the bulk modulus formula?

K = -V dP/dV, or for a finite change K = -V0 x ΔP / ΔV. Compressing 1000 mL of water to 990 mL needs about 22 MPa, so K is 1000 x 22 / 10 = 2200 MPa, or 2.2 GPa.

What are the units of bulk modulus?

Pascals, the same as pressure, usually quoted in GPa for solids and liquids and in kPa for gases. 1 GPa is 1,000,000,000 Pa, about 145,038 psi.

What is compressibility?

Compressibility is the reciprocal of the bulk modulus, β = 1 / K. Water at 2.2 GPa has β of about 4.5e-10 per Pa, or 0.45 per GPa, meaning a 1 GPa pressure rise would cut the volume by about 45 percent if K stayed constant.

How do you find the speed of sound from the bulk modulus?

c = square root of K over ρ. Water with K = 2.2 GPa and ρ = 998 kg/m3 gives 1484.7 m/s. Use the adiabatic modulus, because sound compresses the fluid too quickly for heat to flow.

How is bulk modulus related to Young's modulus?

K = E / (3 (1 - 2ν)) for an isotropic elastic solid. Steel with E = 200 GPa and ν = 0.30 gives K = 166.7 GPa. When ν = 1/3, K equals E.

Why is the bulk modulus of a gas equal to its pressure?

For an ideal gas compressed isothermally, PV is constant, so dP/dV = -P/V and K = P. For adiabatic compression K = γP, which is 1.4 times the pressure for air. At one atmosphere that is about 101.3 kPa isothermal and 141.9 kPa adiabatic.

What is a high bulk modulus?

A high modulus means a material that is hard to compress. Steel is around 160 GPa, water 2.2 GPa and air only about 0.1 MPa. Liquids are nearly incompressible compared with gases but still compress measurably in the deep ocean.

How much does water compress at the bottom of the ocean?

At about 100 MPa, roughly the pressure near 10 km depth, a constant K of 2.2 GPa gives a volume drop of 4.5 percent and a density rise of 4.8 percent. K itself rises with pressure, so the true change is somewhat smaller.

Can the bulk modulus be negative?

Not for a stable material, because a pressure increase must shrink it. A negative result from measured data means the pressure and volume changes have inconsistent signs or the measurement is wrong.

What is the difference between isothermal and adiabatic bulk modulus?

The isothermal value applies when temperature is held constant and the adiabatic (isentropic) one when no heat flows. The adiabatic modulus is larger, and it is the right one for sound waves.