Belt Length Calculator

Find the length of an open or crossed belt around two pulleys, the centre distance for a belt you already have, and the resulting speed ratio.

⚙️ Belt Length Calculator
Belt arrangement
Large pulley (D)
mm
501000
Small pulley (d)
mm
20500
Centre distance (C)
mm
1003000
Belt length (L)
mm
Driver pulley
mm
Driven pulley
mm
Driver speed
rpm
1005000
Belt slip
%
Belt length L
—
Belt length (m)
—
Centre distance C
—
Wrap, small pulley
—
Wrap, large pulley
—
Exact geometric length
—
Speed ratio D : d
—
Driven speed
—
Speed ratio
—
Belt speed
—
Belt speed (ft/min)
—
Drive type
—

⚙️ What is a Belt Length Calculator?

Belt length is the total length of a closed loop of belt needed to run around two pulleys held a fixed distance apart. A belt drive transfers rotation and power between two shafts using friction (flat and V-belts) or teeth (timing belts), and the loop must be the right length so it can wrap both pulleys with the correct tension. Too short and it will not fit or will be over-tensioned. Too long and it slips, flaps or wears quickly. The calculator turns the two pulley diameters and the centre distance into a belt length, and reverses the calculation when you already have a belt and need to know where to mount the motor.

The calculation is used in many practical situations. Mechanics and machine builders size replacement belts for lathes, drill presses, compressors, fans and conveyors. Engineers lay out pulley drives for pumps and motors. Hobbyists size belts for 3D printers, bicycles and workshop tools. Teachers use it to explain how speed changes between a small and a large pulley. For each job you need the length for ordering, the wrap angle to judge grip, the speed ratio to know how fast the driven machine runs, and the belt speed to stay inside the belt's rating.

A few distinctions matter. The standard formula is an approximation of the true wrapped path, which this page also gives in exact form for comparison, and for typical drives the two differ by a fraction of a millimetre to a few tenths of a millimetre. An open belt turns both pulleys in the same direction, while a crossed belt reverses the direction and gives more wrap. A belt drive is also not a gear train: it gives a speed ratio equal to the diameter ratio, but it can slip, and it does not fix the phase between shafts unless it is a toothed belt. For a toothed gear set see the gear ratio calculator, and for a vehicle drivetrain multiplication see the crawl ratio calculator.

The calculator has three modes: belt length from centre distance, centre distance from a known belt length, and a speed mode with driven speed, slip and belt speed. Each mode has a chart that marks your values.

📐 Formula

L  =  2C + π(D + d) / 2 + (D − d)² / (4C)
L = belt length (mm), measured along the pitch line
D, d = large and small pulley diameters (mm)
C = centre distance between the two pulley shafts (mm)
Crossed belt: L = 2C + π(D + d) / 2 + (D + d)² / (4C)
Wrap angles (open): small pulley = 180° − 2α, large pulley = 180° + 2α, with sin α = (D − d) / 2C. For a crossed belt both are 180° + 2α with sin α = (D + d) / 2C.
Centre distance: C = [B + √(B² − 2q²)] / 4, where B = L − π(D + d)/2 and q = D − d (open) or D + d (crossed)
Speed: n2 = n1 (D1 / D2)(1 − slip) and belt speed v = π D1 n1 / 60
Example: D = 300 mm, d = 100 mm, C = 800 mm, open belt gives L = 2240.82 mm

📖 How to Use This Calculator

Steps

1
Choose the mode and belt type. Use Belt length to size a belt, Centre distance to find the shaft spacing for a belt you have, or Speed for driven rpm and belt speed. Choose open or crossed where it applies.
2
Enter pulleys and distance. Type the large and small pitch diameters in millimetres and either the centre distance or the belt length. In Speed mode enter the driver and driven diameters, the driver rpm and any slip.
3
Read and check. Note the belt length or centre distance, the wrap angles and the exact length, then look at the chart to see how sensitive the result is to the distance.

💡 Example Calculations

Example 1 — Open Belt Length

D = 300 mm, d = 100 mm, C = 800 mm, open belt

1
2C = 1600.00 mm and π(D + d)/2 = π × 400 / 2 = 628.32 mm
2
(D − d)²/(4C) = 200² / 3200 = 12.50 mm
3
L = 1600 + 628.32 + 12.50 = 2240.82 mm. The wrap angles are 165.64° on the small pulley and 194.36° on the large one, and the exact geometric length is 2240.83 mm.
Belt length = 2240.82 mm (2.2408 m), speed ratio 3 : 1
Try this example →

Example 2 — Same Pulleys With a Crossed Belt

D = 300 mm, d = 100 mm, C = 800 mm, crossed belt

1
2C + π(D + d)/2 = 1600 + 628.32 = 2228.32 mm
2
(D + d)²/(4C) = 400² / 3200 = 50.00 mm, so L = 2278.32 mm
3
Both pulleys now have a wrap of 208.96°, which is more than the 165.64° of the open belt on the small pulley. The exact length is 2278.58 mm, 0.26 mm above the approximation.
Belt length = 2278.32 mm, wrap = 208.96° on both pulleys
Try this example →

Example 3 — Centre Distance for a Known Open Belt

D = 300 mm, d = 100 mm, belt length L = 2400 mm, open belt

1
B = 2400 − 628.32 = 1771.68 mm and 2(D − d)² = 2 × 40000 = 80000
2
C = [1771.68 + √(1771.68² − 80000)] / 4 = [1771.68 + 1748.96] / 4 = 880.16 mm
3
Check: L = 2 × 880.16 + 628.32 + 40000 / 3520.65 = 2400.00 mm. Wrap angles are 166.95° and 193.05°.
Centre distance = 880.16 mm
Try this example →

Example 4 — Centre Distance for a Crossed Belt

D = 200 mm, d = 80 mm, belt length L = 1500 mm, crossed belt

1
B = 1500 − π × 280 / 2 = 1500 − 439.82 = 1060.18 mm, and q = D + d = 280, so 2q² = 156800
2
C = [1060.18 + √(1060.18² − 156800)] / 4 = 510.91 mm
3
The wrap on each pulley is 211.81° and the speed ratio is 200 / 80 = 2.5 : 1, with the pulleys turning in opposite directions.
Centre distance = 510.91 mm, wrap = 211.81°
Try this example →

Example 5 — Speed Reduction Drive

Motor pulley 100 mm at 1450 rpm driving a 300 mm pulley, no slip

1
Speed ratio = 300 / 100 = 3 : 1, a speed reduction
2
Driven speed = 1450 × 100 / 300 = 483.33 rpm
3
Belt speed = π × 0.1 × 1450 / 60 = 7.592 m/s = 1495 ft/min
Driven speed = 483.33 rpm, belt speed = 7.592 m/s
Try this example →

Example 6 — Speed With 2 Percent Slip

Pulley 120 mm at 2880 rpm driving a 200 mm pulley, 2 percent slip

1
Ideal driven speed = 2880 × 120 / 200 = 1728 rpm
2
With slip: 1728 × (1 − 0.02) = 1693.44 rpm
3
Belt speed = π × 0.12 × 2880 / 60 = 18.096 m/s, fairly high, so check the belt rating. The 2 percent slip value is an assumed illustration.
Driven speed = 1693.44 rpm, belt speed = 18.096 m/s
Try this example →

❓ Frequently Asked Questions

What is the formula for belt length?+
For an open belt drive, L = 2C + pi(D + d) / 2 + (D - d) squared / (4C), where D and d are the large and small pulley diameters and C is the centre distance. For a crossed belt the last term becomes (D + d) squared / (4C).
How do I find the centre distance from the belt length?+
Let B = L - pi(D + d) / 2. For an open belt, C = [B + sqrt(B squared - 2(D - d) squared)] / 4. For a crossed belt use (D + d) in place of (D - d). The calculator shows an error if the belt is too short to fit around the pulleys.
What is the wrap angle of an open belt?+
On the small pulley it is 180 degrees minus 2 asin((D - d) / 2C), and on the large pulley it is 180 degrees plus the same amount. The small pulley has the smaller wrap and so limits the grip. A minimum wrap near 120 degrees is a commonly quoted rule of thumb (illustrative only), so check the belt maker data.
What is the difference between an open and a crossed belt drive?+
An open belt runs straight between the pulleys, so both turn in the same direction. A crossed belt twists in a figure eight so the pulleys turn in opposite directions. Crossed belts give a larger wrap but the belt rubs against itself, so they are used with flat belts at lower speeds and need more space between pulleys.
How do I calculate belt speed?+
Belt speed is v = pi D n / 60, with D in metres and n in rpm giving metres per second. Because the belt moves at the same speed over both pulleys (ignoring slip), you can use either pulley, as long as you use its own diameter and its own rpm.
How is the speed ratio of a belt drive calculated?+
The speed ratio is the driven diameter divided by the driver diameter, and the driven speed is the driver speed times the inverse of that ratio, reduced a little by slip. A 100 mm motor pulley driving a 300 mm pulley gives a 3 to 1 reduction.
How accurate is the belt length formula?+
It is a close approximation when the centre distance is several times the pulley diameters. The calculator also shows the exact geometric length from the tangent construction. In the 300 mm and 100 mm example the difference is about 0.01 mm for an open belt and 0.26 mm for a crossed belt.
Is belt length the same for V-belts and flat belts?+
The geometry is the same, but you must use the pitch diameter for V-belts and the pitch length for the belt size. Manufacturers list nominal pitch, inside or outside lengths, which differ by a fixed amount from the pitch length, so convert before ordering.
How is this different from a gear ratio calculator?+
A gear ratio is set by tooth counts and has no slip, while a friction belt drive has a ratio from pulley diameters and some slip. A belt drive also needs the right loop length for the centre distance, which gears do not. The ratio arithmetic is similar, so the speed mode here parallels the gear case.
What happens if my pulleys are the same size?+
With D equal to d, an open belt has a wrap of 180 degrees on both pulleys and the length is simply 2C + pi D. A crossed belt with equal pulleys still has more than 180 degrees of wrap. The speed ratio is 1 to 1 for both.
Can the centre distance be too small?+
Yes. For an open belt the centre distance must exceed (D - d) / 2, and for a crossed belt it must exceed (D + d) / 2, or the belt cannot wrap both pulleys. In practice you want much more, because a short centre distance gives a poor wrap angle and rapid belt flexing.

What is the formula for belt length?

For an open belt drive, L = 2C + pi(D + d) / 2 + (D - d)^2 / (4C), where D and d are the large and small pulley diameters and C is the centre distance. For a crossed belt the last term becomes (D + d)^2 / (4C).

How do I find the centre distance from the belt length?

Let B = L - pi(D + d) / 2. For an open belt, C = [B + sqrt(B^2 - 2(D - d)^2)] / 4, and for a crossed belt use (D + d) in place of (D - d).

What is the wrap angle of an open belt?

The wrap angle on the small pulley is 180 degrees minus 2 asin((D - d) / 2C) and on the large pulley it is 180 degrees plus the same amount. The small pulley always has the smaller wrap and limits the grip.

What is the difference between an open and a crossed belt?

An open belt runs straight between pulleys so both turn the same way, while a crossed belt twists in a figure eight so the pulleys turn in opposite directions. Crossed belts have a larger wrap angle but suffer more wear where the belt rubs itself.

How is belt speed calculated?

Belt speed is v = pi D n / 60 in consistent units, where D is the driver pulley diameter and n is its speed in rpm. With D in millimetres, divide by 1000 to get metres per second.

What is the difference between an open and a crossed belt drive?

An open belt runs straight between the pulleys, so both turn in the same direction. A crossed belt twists in a figure eight so the pulleys turn in opposite directions. Crossed belts give a larger wrap but the belt rubs against itself, so they are used with flat belts at lower speeds and need more space between pulleys.

How do I calculate belt speed?

Belt speed is v = pi D n / 60, with D in metres and n in rpm giving metres per second. Because the belt moves at the same speed over both pulleys (ignoring slip), you can use either pulley, as long as you use its own diameter and its own rpm.

How is the speed ratio of a belt drive calculated?

The speed ratio is the driven diameter divided by the driver diameter, and the driven speed is the driver speed times the inverse of that ratio, reduced a little by slip. A 100 mm motor pulley driving a 300 mm pulley gives a 3 to 1 reduction.

How accurate is the belt length formula?

It is a close approximation when the centre distance is several times the pulley diameters. The calculator also shows the exact geometric length from the tangent construction. In the 300 mm and 100 mm example the difference is about 0.01 mm for an open belt and 0.26 mm for a crossed belt.