Beat Frequency Calculator

Find how fast two close tones beat, what pitch you hear, and how far out of tune a string is from the beats you count.

🎵 Beat Frequency Calculator
Frequency 1 (f1)
Hz
Frequency 2 (f2)
Hz
Amplitude of tone 2 relative to tone 1
0.12
Reference string or tuning fork frequency
Hz
Beats counted
Counting time
s
Beat frequency
—
Beat period
—
Beats per minute
—
Average (heard) frequency
—
Frequency ratio
—
Interval
—
Loudest (amplitude of tone 1 = 1)
—
Quietest
—
Modulation depth
—

Beat frequency
—
If the string is sharp
—
Sharp by
—
If the string is flat
—
Flat by
—
Tension change if sharp
—
Tension change if flat
—
Beat period
—

🎵 What is Beat Frequency?

Beat frequency is the rate at which the loudness of a sound rises and falls when two tones of slightly different frequency are heard together. The two waves drift in and out of step. When their peaks line up they add and the sound is loud, and half a beat later a peak meets a trough and they partly cancel, so the sound is quiet. The number of loud swells per second is simply the difference of the two frequencies, fbeat = |f1 − f2|.

Beats are a practical tool. Piano tuners and guitarists listen for them to bring two strings or a string and a tuning fork into unison: as the pitches converge the beats slow down, and when they stop the frequencies match. Organ builders sometimes add a deliberately detuned rank of pipes (a celeste) to give a shimmering sound. Radio operators use the same idea as zero beat when matching a carrier, and engineers use beat counting to compare two oscillators, two rotating machines or two propellers. Pilots of twin-engine aircraft hear the throb of two slightly mismatched engines in the same way.

A few points are easy to mix up. The pitch you hear is not the beat frequency but the average frequency (f1 + f2)/2, modulated in loudness at the beat rate. Beats appear only when the frequencies are close. As the gap widens past roughly 10 to 15 hertz the swells blur into roughness and then into two separate tones; this threshold is a rule of thumb that depends on pitch and listener. Beats are also different from the Doppler shift, which is a change of pitch caused by motion, covered in the Doppler effect calculator, and different from binaural beats, an auditory illusion with no physical beating in the air.

This calculator has two modes. Two tones takes any two frequencies, optionally with unequal loudness, and gives the beat frequency, period, average pitch and interval in cents together with a waveform and envelope chart. Tune by ear takes a reference frequency and a count of beats over a time and returns the two string frequencies that could cause them, how many cents out they are and the tension change needed to bring the string into unison.

📐 Formula

fbeat  =  | f1 − f2 |
fbeat = beat frequency (Hz), the number of loudness swells per second
f1, f2 = the two tone frequencies (Hz)
Beat period: Tbeat = 1 / fbeat
Average (heard) frequency: favg = ( f1 + f2 ) / 2
Interval: cents = 1200 × log2( f2 / f1 )
Waveform: A1 sin(2π f1 t) + A2 sin(2π f2 t), with envelope √( A1² + A2² + 2 A1 A2 cos(2π fbeat t) ), so the loudest value is A1 + A2 and the quietest is |A1 − A2|
Tuning: fbeat = beats counted / time, the string is at fref ± fbeat, and the tension ratio is ( fref / fstring )²
Example: f1 = 440 Hz and f2 = 442 Hz give fbeat = 2 Hz and favg = 441 Hz

📖 How to Use This Calculator

Steps

1
Choose a mode. Pick Two tones when you know both frequencies, or Tune by ear when you have counted beats against a reference.
2
Enter the values. Type the two frequencies in hertz and, if the tones differ in loudness, the relative amplitude of tone 2. For tuning, enter the reference frequency, the number of beats and the time you counted for.
3
Read the results and the chart. See the beat frequency, period and interval, or the two possible string frequencies and tension change. The chart shows the waveform and its envelope, or the beat rate against tuning error.

💡 Example Calculations

Example 1 — Two Piano Strings at 440 and 442 Hz

f1 = 440 Hz, f2 = 442 Hz, equal amplitudes

1
fbeat = |440 − 442| = 2.000 Hz, which is 120.0 beats per minute
2
Beat period = 1 / 2 = 0.5000 s and the heard pitch is (440 + 442) / 2 = 441.000 Hz
3
Interval = 1200 × log2(442 / 440) = 7.85 cents. With equal amplitudes the sound fades to silence at each beat minimum.
Beat frequency = 2.000 Hz (period 0.5000 s)
Try this example →

Example 2 — Textbook Pair at 256 and 250 Hz

f1 = 256 Hz, f2 = 250 Hz, equal amplitudes

1
fbeat = |256 − 250| = 6.000 Hz, or 360.0 beats per minute
2
Beat period = 1 / 6 = 0.1667 s, average pitch = 253.000 Hz
3
The frequency ratio is 1.02400 and the interval is 41.06 cents, a bit under half a semitone. Six swells per second is fast but still countable.
Beat frequency = 6.000 Hz (period 0.1667 s)
Try this example →

Example 3 — Unequal Loudness

f1 = 440 Hz, f2 = 444 Hz, tone 2 half as loud as tone 1

1
fbeat = |440 − 444| = 4.000 Hz and the period is 0.2500 s
2
Loudest amplitude = 1 + 0.5 = 1.500 and quietest = |1 − 0.5| = 0.500
3
Modulation depth = (1.5 − 0.5) / (1.5 + 0.5) = 50.0 %. The sound never goes silent, because the weaker tone cannot fully cancel the stronger one.
Beat frequency = 4.000 Hz, depth = 50.0 %
Try this example →

Example 4 — Two Low Frequency Oscillations

f1 = 10 Hz, f2 = 12 Hz, equal amplitudes

1
fbeat = |10 − 12| = 2.000 Hz with a period of 0.5000 s
2
The average frequency is 11.000 Hz, so each beat period holds 5.5 carrier cycles
3
The ratio is 1.20000 and the interval is 315.64 cents. Only 16.5 carrier cycles fit in the chart window, so the chart draws the exact sum of the two tones inside its envelope.
Beat frequency = 2.000 Hz, average = 11.000 Hz
Try this example →

Example 5 — Tuning an A String Against a 440 Hz Fork

Reference 440 Hz, 7 beats counted in 5 seconds

1
fbeat = 7 / 5 = 1.400 Hz, so the beat period is 0.714 s
2
The string is either at 440 + 1.4 = 441.40 Hz (+5.50 cents) or at 440 − 1.4 = 438.60 Hz (−5.52 cents)
3
Tension factor if sharp = (440 / 441.4)² − 1 = −0.63 %, and if flat = (440 / 438.6)² − 1 = +0.64 %, since pitch scales with the square root of tension
Beat rate = 1.400 Hz, string at 441.40 Hz or 438.60 Hz
Try this example →

Example 6 — Low E Guitar String

Reference 82.41 Hz, 6 beats counted in 10 seconds

1
fbeat = 6 / 10 = 0.600 Hz with a beat period of 1.667 s
2
The string is at 83.01 Hz (+12.56 cents) or 81.81 Hz (−12.65 cents)
3
The tension must fall by 1.44 % if it is sharp, or rise by 1.47 % if flat. A beat of only 0.6 Hz is a larger musical error here than 1.4 Hz was at 440 Hz, because the note is so low.
Beat rate = 0.600 Hz, string at 83.01 Hz or 81.81 Hz
Try this example →

❓ Frequently Asked Questions

What is the formula for beat frequency?+
The beat frequency is the absolute difference of the two frequencies, f_beat = |f1 - f2|. Two tones at 440 Hz and 442 Hz produce a beat frequency of 2 Hz, which is two loudness swells per second.
How do you calculate beats per second?+
Subtract the lower frequency from the higher one. The result in hertz is the number of beats per second. Multiply by 60 for beats per minute, or divide 1 by it for the beat period in seconds.
What pitch do you hear when two tones beat?+
You hear a single tone at about the average frequency (f1 + f2)/2 whose loudness rises and falls at the beat frequency. For 440 Hz and 442 Hz that is 441 Hz.
How do beats help you tune a guitar or piano?+
When two strings are close in pitch they beat. As the pitches converge the beats slow down and stop at unison. Count the beats over a few seconds to get the frequency gap, then adjust the tension until the beats disappear.
Can beats tell me if a string is sharp or flat?+
No. A beat rate of 2 Hz means the other string is either 2 Hz above or 2 Hz below. Tighten the string a little: if the beat rate increases it was sharp, if it decreases it was flat.
How many cents is a given beat frequency?+
It depends on pitch. The interval is 1200 log2(f2/f1) cents. A 2 Hz beat at 440 Hz is about 7.85 cents, but the same 2 Hz at 110 Hz is about 31 cents, so low notes need slower beats for the same accuracy.
What is the period of the beats?+
The beat period is 1 divided by the beat frequency. At 2 Hz the loudness repeats every 0.5 seconds. The two tones come back into step once per beat period.
Why do beats stop when the two frequencies are equal?+
At equal frequencies the two waves keep a fixed phase relation, so they add into one steady tone and the envelope no longer changes. The beat frequency is zero and the beat period is infinite.
What happens if the two tones have different loudness?+
The beats are shallower. The amplitude swings between the sum and the difference of the two amplitudes, so the sound never goes completely silent. This calculator reports the maximum, the minimum and the modulation depth.
Are acoustic beats the same as binaural beats?+
No. Acoustic beats happen in the air or in the electrical signal when two tones are added. Binaural beats are an auditory illusion produced when different tones are sent to each ear, with no physical beating in the air.
Why does the chart sometimes show only an envelope?+
A 440 Hz tone has hundreds of cycles inside a few beat periods, more than a screen can draw. When there are more than 80 carrier cycles in the window, the chart shows the envelope only. Low frequency pairs are drawn exactly.
How does string tension change the pitch?+
For a fixed length and mass per length, frequency is proportional to the square root of tension. Raising the pitch by 1 percent needs about 2 percent more tension, which is why the tuning mode reports the tension change as the square of the frequency ratio minus one.

What is the formula for beat frequency?

The beat frequency is the absolute difference of the two frequencies, f_beat = |f1 - f2|. Two tones at 440 Hz and 442 Hz produce a beat frequency of 2 Hz, which is two loudness swells per second.

How do you calculate beats per second?

Subtract the lower frequency from the higher one. The result in hertz is the number of beats per second. Multiply by 60 for beats per minute, or divide 1 by it for the beat period in seconds.

What pitch do you hear when two tones beat?

You hear a single tone at about the average frequency (f1 + f2)/2 whose loudness rises and falls at the beat frequency. For 440 Hz and 442 Hz that is 441 Hz.

How do beats help you tune a guitar or piano?

When two strings are close in pitch they beat. As the pitches converge the beats slow down and stop at unison. Count the beats over a few seconds to get the frequency gap, then adjust the tension until the beats disappear.

Can beats tell me if a string is sharp or flat?

No. A beat rate of 2 Hz means the other string is either 2 Hz above or 2 Hz below. Tighten the string a little: if the beat rate increases it was sharp, if it decreases it was flat.

How many cents is a given beat frequency?

It depends on pitch. The interval is 1200 log2(f2/f1) cents. A 2 Hz beat at 440 Hz is about 7.85 cents, but the same 2 Hz at 110 Hz is about 31 cents, so low notes need slower beats for the same accuracy.

What is the period of the beats?

The beat period is 1 divided by the beat frequency. At 2 Hz the loudness repeats every 0.5 seconds. The two tones come back into step once per beat period.

Why do beats stop when the two frequencies are equal?

At equal frequencies the two waves keep a fixed phase relation, so they add into one steady tone and the envelope no longer changes. The beat frequency is zero and the beat period is infinite.

What happens if the two tones have different loudness?

The beats are shallower. The amplitude swings between the sum and the difference of the two amplitudes, so the sound never goes completely silent. This calculator reports the maximum, the minimum and the modulation depth.

Are acoustic beats the same as binaural beats?

No. Acoustic beats happen in the air or in the electrical signal when two tones are added. Binaural beats are an auditory illusion produced when different tones are sent to each ear, with no physical beating in the air.

Why does the chart show only an envelope sometimes?

A 440 Hz carrier has hundreds of cycles inside a few beat periods, more than a screen can draw. When there are more than 80 carrier cycles in the window, the chart shows the envelope only. Low frequency pairs are drawn exactly.