Angle of Twist Calculator

Find how far a round shaft twists under torque, the surface shear stress, or the torque and diameter that keep the twist within a limit.

🌀 Angle of Twist Calculator
Torque
N·m
Diameters in millimetresinner diameter 0 means a solid shaft
Outer diameter (mm)
Inner diameter (mm)
Allowable shear stress (optional)
MPa
Diameters in millimetresinner diameter 0 means a solid shaft
Outer diameter (mm)
Inner diameter (mm)
Allowable total twist
°
Allowable shear stress (optional)
MPa
Torque
N·m
Allowable total twist
°
Inner to outer diameter ratio0 is a solid shaft, 0.6 is a typical tube
Allowable shear stress (optional)
MPa
Material preset (illustrative)
Shear modulus G
GPa
10100
Shaft length L
m
0.15
Angle of twist
—
Angle in radians
—
Twist per metre
—
Maximum shear stress
—
Polar moment J
—
Torsional stiffness T / theta
—
Torsional rigidity G J
—
Stress check
—

Cross-section of the shaft, to scale: the shaded ring is the load-carrying material.

Allowable torque
—
Governing limit
—
Torque from twist limit
—
Torque from stress limit
—
Twist at that torque
—
Surface stress at that torque
—
Polar moment J
—
Torsional stiffness G J / L
—

Cross-section of the shaft, to scale.

Outer diameter needed
—
Inner diameter
—
Governing limit
—
Diameter from twist limit
—
Diameter from stress limit
—
Twist at that diameter
—
Surface stress
—
Cross-section area
—

Cross-section of the shaft, to scale.

🌀 What is the Angle of Twist?

The angle of twist is how much one end of a loaded shaft rotates relative to the other end when a torque is applied. A drive shaft, a screwdriver, a torsion bar and a rod wound in a lathe chuck all twist a little when loaded. For a straight shaft of uniform circular cross-section the twist is proportional to the torque and the length, and inversely proportional to the product of the shear modulus G and the polar second moment of area J: theta = T L / (G J). The product G J is called the torsional rigidity, and it plays the same role for twisting that stiffness plays for a spring.

Engineers care about the twist for two reasons. Strength is one: the same torque produces a shear stress, largest at the surface, that must stay below an allowable value. Stiffness is the other: even when the stress is acceptable, too much twist ruins the timing of a camshaft, misaligns gears, makes a servo drive hunt, or lets a measuring torsion bar read inaccurately. Real design specifications often cap the twist in degrees per metre, which is why this page reports it directly. The two checks do not always agree, so the calculator can solve for the allowable torque or the required diameter against both limits and tell you which one governs.

The strong dependence on size is the key feature. J grows with the fourth power of the diameter, so doubling the diameter makes a shaft 16 times stiffer in twist, while doubling the length merely doubles the twist. That is why hollow tubes are so efficient: the material close to the axis is lightly stressed, so removing it saves weight with little loss of stiffness. A hollow shaft with a diameter ratio of 0.6 keeps about 87 percent of the stiffness of the solid shaft while removing 36 percent of the material.

This page differs from the neighbouring tools. The rotational stiffness calculator centres on the torsional spring constant and natural frequency, and the polar moment of inertia calculator centres on section properties. The shear stress calculator covers transverse shear in beams, which is a different loading from torsion. Here the focus is the design question: how much will this shaft twist, how much torque can it take, and how big must it be. The material presets are illustrative starting values, not certified data.

📐 Formula

θ = T L / (G J)    J = π (do4 − di4) / 32    τmax = T (do / 2) / J
θ = angle of twist in radians (multiply by 180 / π for degrees). The twist per metre is θ / L.
T = torque in N·m, L = shaft length in m, G = shear modulus in Pa (entered in GPa).
J = polar second moment of area in m4. For a solid shaft di = 0, giving J = π d4 / 32.
τmax = maximum shear stress at the outer surface in Pa. A shaft is acceptable when τmax is no more than the allowable stress.
Solve for torque: T = θ G J / L from the twist limit and T = τ J / (do / 2) from the stress limit. The smaller one governs.
Solve for diameter: do = (32 J / (π (1 − k4)))1/4 with J = T L / (G θ) and k = di / do, and do = (16 T / (π τ (1 − k4)))1/3 from the stress limit. The larger one governs.
Example: T = 500 N·m, L = 1.2 m, G = 79.3 GPa and a 40 mm solid shaft give θ = 0.0301 rad = 1.725°.

📖 How to Use This Calculator

Steps

1
Choose a mode. Use Find the twist for a shaft you already have, Solve for torque to get the largest torque within a twist or stress limit, and Solve for diameter to size a new shaft.
2
Enter the material and length. Pick an illustrative preset or type the shear modulus G in GPa, then the shaft length in metres. These two apply to every mode.
3
Enter the load, section or limits. Type the torque and diameters, or the allowable twist and the optional allowable shear stress. Use an inner diameter of 0 for a solid shaft.
4
Read the results. The twist in radians, degrees and degrees per metre, the surface stress, stiffness and governing limit appear with a cross-section and a chart for the mode.

💡 Example Calculations

Example 1 — A Solid Steel Shaft

A 40 mm solid steel shaft (G = 79.3 GPa) 1.2 m long carries 500 N·m

1
J = π × 404 / 32 = 251,327 mm4, so G J = 79.3 GPa × 251,327 mm4 = 19,930.3 N·m2.
2
θ = 500 × 1.2 / 19,930.3 = 0.03010 rad = 1.725°, or 1.437°/m.
3
τ = 500 × 0.020 / 2.51327 × 10−7 = 39.79 MPa.
Twist = 1.725°, surface shear stress = 39.79 MPa
Try this example →

Example 2 — A Hollow Aluminium Tube

A 50 mm by 40 mm aluminium tube (G = 25.5 GPa, illustrative) 0.8 m long carries 200 N·m, with a 30 MPa stress limit

1
J = π (504 − 404) / 32 = 362,265 mm4 and G J = 9,237.8 N·m2.
2
θ = 200 × 0.8 / 9,237.8 = 0.01732 rad = 0.9924°.
3
τ = 200 × 0.025 / 3.62265 × 10−7 = 13.80 MPa, which uses 46.0 % of the 30 MPa limit.
Twist = 0.9924°, stress = 13.80 MPa (46.0 % of the limit)
Try this example →

Example 3 — Allowable Torque on a 30 mm Shaft

A 30 mm solid steel shaft, 1 m long, may twist at most 1° and see at most 20 MPa

1
J = π × 304 / 32 = 79,522 mm4.
2
Twist limit: T = 0.01745 × 79.3 GPa × 79,522 mm4 / 1 m = 110.1 N·m.
3
Stress limit: T = 20 MPa × 79,522 mm4 / 15 mm = 106.0 N·m, which is smaller, so the stress limit governs and the twist is 0.9634°.
Allowable torque = 106.0 N·m, set by the shear stress limit
Try this example →

Example 4 — Sizing a Solid Drive Shaft

A 1.5 m steel shaft must carry 1000 N·m with at most 2° of twist and 40 MPa of shear stress

1
Twist limit: J = 1000 × 1.5 / (79.3 GPa × 0.03491 rad), giving do = 48.47 mm.
2
Stress limit: do = (16 × 1000 / (π × 40 MPa))1/3 = 50.31 mm, which is larger and governs.
3
At 50.31 mm the twist is only 1.723° and the stress is exactly 40.00 MPa.
Outer diameter needed = 50.31 mm, governed by the shear stress limit
Try this example →

Example 5 — A Hollow Shaft With a Ratio of 0.6

The same 1000 N·m, 1.5 m and 2° limit, now as a tube with di / do = 0.6 and no stress limit

1
J = 1000 × 1.5 / (79.3 GPa × 0.03491 rad) = 541,900 mm4 (rounded).
2
do = (32 J / (π (1 − 0.64)))1/4 = 50.18 mm, so di = 30.11 mm.
3
The surface stress is 46.30 MPa. The tube uses 1,265.8 mm2 of material against 1,987.8 mm2 for the solid shaft in Example 4.
Outer diameter = 50.18 mm, inner diameter = 30.11 mm, twist = 2.000°
Try this example →

❓ Frequently Asked Questions

How do you calculate the angle of twist of a shaft?+
Use theta = T L / (G J) in radians, where T is torque, L is length, G is the shear modulus and J is the polar second moment of area. A 40 mm steel shaft 1.2 m long carrying 500 N·m twists 0.0301 rad, or 1.725 degrees.
What is the polar moment of area of a solid and a hollow shaft?+
For a solid circular shaft J = pi d to the fourth over 32. For a hollow shaft J = pi (do to the fourth minus di to the fourth) over 32. A 40 mm solid shaft has J of 251,327 mm to the fourth.
How do you find the shear stress in a twisted shaft?+
The maximum shear stress is at the outer surface and equals tau = T r / J, with r the outer radius. The same 500 N·m on a 40 mm steel shaft gives 39.79 MPa.
What is a safe angle of twist per metre?+
It depends on the application. Many machine shafts are limited to a fraction of a degree per metre to keep gears and couplings aligned, while slow drives may allow more. This calculator reports degrees per metre so you can compare with your own limit.
Does a hollow shaft twist more than a solid one?+
For the same outer diameter, yes, because J is smaller. But per unit of material a hollow shaft is far more efficient, since the material near the axis carries little stress. A 50 mm by 40 mm aluminium tube is much stiffer per kilogram than a solid bar.
How do you find the torque for a given twist?+
Rearrange to T = theta G J / L. For a 30 mm solid steel shaft 1 m long and a 1 degree limit, T is 110.1 N·m. If a surface stress limit gives a smaller torque, that one governs.
How do you find the shaft diameter for a given twist?+
Find J = T L / (G theta), then do = (32 J / (pi (1 minus k to the fourth)))^(1/4), with k the inner to outer diameter ratio. Also check the stress limit and use the larger diameter.
What is torsional rigidity?+
Torsional rigidity is the product G J, in N·m squared. Dividing it by the length gives the torsional stiffness T over theta in N·m per radian. The 40 mm steel shaft above has G J of 19,930 N·m squared.
Is this formula valid for square or I-shaped shafts?+
No. theta = T L / (G J) with J as the polar moment is exact only for circular sections. Other sections warp, so their torsion constant is much smaller than the polar moment.
How is angle of twist different from shear strain?+
The angle of twist is the rotation of one end relative to the other over the length. Shear strain at the surface is gamma = r theta / L, so it depends on both the twist and the radius.
What shear modulus should I use for steel?+
About 79 to 80 GPa is commonly quoted for steel at room temperature, with 79.3 GPa a typical figure. Stainless and alloy steels differ slightly, so use the value for your grade if you have it.

How do you calculate the angle of twist of a shaft?

Use theta = T L / (G J) in radians, where T is torque, L is length, G is the shear modulus and J is the polar second moment of area. A 40 mm steel shaft 1.2 m long carrying 500 N·m twists 0.0301 rad, or 1.725 degrees.

What is the polar moment of area of a solid and a hollow shaft?

For a solid circular shaft J = pi d to the fourth over 32. For a hollow shaft J = pi (do to the fourth minus di to the fourth) over 32. A 40 mm solid shaft has J of 251,327 mm to the fourth.

How do you find the shear stress in a twisted shaft?

The maximum shear stress is at the outer surface and equals tau = T r / J, with r the outer radius. The same 500 N·m on a 40 mm steel shaft gives 39.79 MPa.

What is a safe angle of twist per metre?

It depends on the application. Many machine shafts are limited to a fraction of a degree per metre to keep gears and couplings aligned, while slow drives may allow more. This calculator reports degrees per metre so you can compare with your own limit.

Does a hollow shaft twist more than a solid one?

For the same outer diameter, yes, because J is smaller. But per unit of material a hollow shaft is far more efficient, since the material near the axis carries little stress. A 50 mm by 40 mm aluminium tube is much stiffer per kilogram than a solid bar.

How do you find the torque for a given twist?

Rearrange to T = theta G J / L. For a 30 mm solid steel shaft 1 m long and a 1 degree limit, T is 110.1 N·m. If a surface stress limit gives a smaller torque, that one governs.

How do you find the shaft diameter for a given twist?

Find J = T L / (G theta), then do = (32 J / (pi (1 minus k to the fourth)))^(1/4), with k the inner to outer diameter ratio. Also check the stress limit and use the larger diameter.

What is torsional rigidity?

Torsional rigidity is the product G J, in N·m squared. Dividing it by the length gives the torsional stiffness T over theta in N·m per radian. The 40 mm steel shaft above has G J of 19,930 N·m squared.

Is this formula valid for square or I-shaped shafts?

No. theta = T L / (G J) with J as the polar moment is exact only for circular sections. Other sections warp, so their torsion constant is much smaller than the polar moment.

How is angle of twist different from shear strain?

The angle of twist is the rotation of one end relative to the other over the length. Shear strain at the surface is gamma = r theta / L, so it depends on both the twist and the radius.