Acoustic Impedance Calculator

Find the characteristic acoustic impedance of a medium, then see how much sound is reflected and transmitted when a wave crosses into another one.

🔊 Acoustic Impedance Calculator
Medium
Density (ρ)
kg/m³
Sound speed (c)
m/s
RMS sound pressure (p)
Pa
Medium 1 (wave comes from here)
Density 1
kg/m³
Sound speed 1
m/s
Medium 2 (wave enters here)
Density 2
kg/m³
Sound speed 2
m/s
Characteristic impedance Z
—
Z in base units
—
Compared with air
—
Particle velocity (RMS)
—
Intensity p²/Z
—
Intensity level (re 10-12 W/m²)
—

Intensity transmitted (T)
—
Intensity reflected (R)
—
Transmission loss
—
Reflection level below incident
—
Pressure reflection r
—
Pressure transmission t
—
Z1
—
Z2
—
Ratio Z2/Z1
—
Ideal matching layer
—

🔊 What is Acoustic Impedance?

Acoustic impedance measures how much a medium resists being set into motion by a sound wave. For a plane wave, the characteristic acoustic impedance is Z = ρ c, the density of the medium times the speed of sound in it. Its SI unit is the pascal second per metre (Pa·s/m), which is also called the rayl. A high impedance means a large pressure is needed to produce a given particle velocity, like a stiff and heavy medium. Air is a low impedance medium at about 413 rayl, while water is near 1.48 million rayl and steel is above 46 million rayl.

The idea matters whenever sound crosses a boundary. At the interface between two media the wave splits into a reflected part and a transmitted part, and the split depends only on the two impedances. Engineers use this to design ultrasound transducers and their matching layers, to explain why a hydrophone must be coupled to water, to estimate how well a wall isolates noise, to choose the gel used on skin during a medical scan, and to design horns and ducts that couple a small driver to open air. Musical instrument makers use it too, because a soundboard has to move air efficiently.

Two points are often confused. First, the characteristic impedance of a medium is a property of the material, while the impedance of a duct, a horn or a membrane also depends on its geometry and frequency. Second, this page is about ordinary acoustic waves in fluids and solids at normal incidence. The same product of density and velocity is used in geophysics, but there it is applied to rock layers and to P-waves or S-waves at varying angles, which is covered separately in the seismic impedance and reflection coefficient calculator. For absorption in seawater see the acoustic absorption coefficient calculator, and to find the sound speed itself use the speed of sound calculator.

This calculator has two modes. The first gives Z for any density and sound speed, together with the particle velocity and intensity produced by a chosen RMS pressure and a table of typical materials for comparison. The second takes two media and gives the reflected and transmitted intensity, the pressure coefficients, the mismatch loss in decibels and the impedance of an ideal quarter-wave matching layer, with a chart that shows how reflection grows as the impedance ratio moves away from one.

📐 Formula

Z  =  ρ × c
Z = characteristic acoustic impedance (rayl = Pa·s/m = kg/(m²·s))
ρ = density of the medium (kg/m³)
c = speed of sound in the medium (m/s)
Plane wave relations: particle velocity u = p / Z and intensity I = p² / Z for RMS pressure p
Intensity reflection: R = ( (Z2 − Z1) / (Z2 + Z1) )²
Intensity transmission: T = 4 Z1 Z2 / (Z1 + Z2)² = 1 − R
Pressure coefficients: r = (Z2 − Z1) / (Z2 + Z1) and t = 2 Z2 / (Z1 + Z2)
Mismatch loss: L = −10 log10(T) dB, and the ideal matching layer has Zm = √(Z1 Z2)
Example: air (Z = 413.2 rayl) into fresh water (Z = 1.479 MRayl) gives T = 0.1117 %

📖 How to Use This Calculator

Steps

1
Choose a mode. Pick Impedance of a medium to compute Z = ρ c, or Reflection at an interface to compare two media.
2
Enter the media. Choose a preset for each medium or type your own density in kg/m³ and sound speed in m/s. Editing a value switches the preset to Custom. In the first mode also enter an RMS sound pressure.
3
Read the results. The first mode gives Z, particle velocity, intensity and a comparison table. The second gives the transmitted and reflected shares, the pressure coefficients, the loss in dB, the matching layer impedance and a chart marked at your impedance ratio.

💡 Example Calculations

The densities and sound speeds used here are typical round values near 20 C and are illustrative. Real materials vary with temperature, composition and wave type.

Example 1 — Impedance of Air and a 1 Pa Wave

Air at 20 C: ρ = 1.204 kg/m³, c = 343.2 m/s, p = 1 Pa RMS

1
Z = 1.204 × 343.2 = 413.2 rayl
2
Particle velocity u = 1 / 413.2 = 2.4201 mm/s
3
Intensity I = 1² / 413.2 = 2.420e-3 W/m², which is 10 log10(2.420e-3 / 1e-12) = 93.8 dB
Z = 413.2 rayl, u = 2.4201 mm/s, I = 2.420e-3 W/m²
Try this example →

Example 2 — A 100 Pa Wave in Fresh Water

Fresh water at 20 C: ρ = 998.2 kg/m³, c = 1482 m/s, p = 100 Pa RMS

1
Z = 998.2 × 1482 = 1 479 332 rayl = 1.479 MRayl, which is 3580 times the impedance of air
2
Particle velocity u = 100 / 1 479 332 = 0.0676 mm/s
3
Intensity I = 100² / 1 479 332 = 6.760e-3 W/m². The pressure is 100 times larger than Example 1 but the particle velocity is 36 times smaller.
Z = 1.479 MRayl, u = 0.0676 mm/s, I = 6.760e-3 W/m²
Try this example →

Example 3 — Air to Water

Sound in air (413.2 rayl) meets the surface of fresh water (1.479 MRayl)

1
Ratio Z2/Z1 = 1 479 332 / 413.2 = 3580
2
r = (1 479 332 − 413.2) / (1 479 332 + 413.2) = 0.9994, so R = r² = 99.89 %
3
T = 4 × 413.2 × 1 479 332 / (1 479 745)² = 0.1117 %, a transmission loss of 29.52 dB
Transmitted = 0.1117 %, reflected = 99.89 %, loss = 29.52 dB
Try this example →

Example 4 — Water to Steel Hull

Fresh water (1.479 MRayl) to steel (ρ = 7850, c = 5900, Z = 46.315 MRayl)

1
Ratio Z2/Z1 = 46 315 000 / 1 479 332 = 31.31
2
r = (46.315 − 1.479) / (46.315 + 1.479) = 0.9381, so R = 88.00 %
3
T = 1 − R = 12.00 %, a loss of 9.21 dB. The ideal matching layer would have √(1.479 × 46.315) = 8.277 MRayl.
Transmitted = 12.00 %, reflected = 88.00 %, loss = 9.21 dB
Try this example →

Example 5 — Soft Tissue to Bone

Soft tissue (ρ = 1060, c = 1540, Z = 1.632 MRayl) to cortical bone (ρ = 1900, c = 4080, Z = 7.752 MRayl)

1
Ratio Z2/Z1 = 7 752 000 / 1 632 400 = 4.749
2
r = (7.752 − 1.632) / (7.752 + 1.632) = 0.6521, so R = 42.52 %
3
T = 57.48 %, a loss of 2.41 dB. This strong echo from bone is why ultrasound images show a bright bone surface with a shadow behind it.
Transmitted = 57.48 %, reflected = 42.52 %, loss = 2.41 dB
Try this example →

❓ Frequently Asked Questions

What is acoustic impedance and how do you calculate it?+
For a plane wave the characteristic acoustic impedance is Z = rho c, the density times the speed of sound. Its SI unit is the pascal second per metre, called the rayl. Air at 20 C gives about 413 rayl, and the calculator evaluates the product for any density and speed you enter.
What is the acoustic impedance of air?+
About 413 rayl (Pa s/m) at 20 C, from a density of 1.204 kg/m3 and a sound speed of 343.2 m/s. It changes slightly with temperature and pressure, and some references round it to 415 rayl.
What is the acoustic impedance of water?+
About 1.48 million rayl (1.48 MRayl) for fresh water at 20 C, from 998.2 kg/m3 and 1482 m/s. Seawater is a little higher, near 1.54 MRayl with the typical values used in the presets.
How do you calculate the sound reflection coefficient?+
At normal incidence the pressure reflection coefficient is r = (Z2 - Z1)/(Z2 + Z1) and the intensity reflection is R = r squared. The transmitted intensity share is T = 1 - R = 4 Z1 Z2/(Z1 + Z2) squared.
Why does sound not pass easily from air into water?+
The impedances differ by a factor of about 3580, so 99.89 percent of the incident intensity is reflected and only about 0.11 percent is transmitted, a loss of about 29.5 dB. The mismatch, not absorption, is what keeps most sound out of the water.
What is impedance mismatch loss in dB?+
It is minus 10 log10 of the intensity transmission T. A perfect match (Z1 = Z2) gives 0 dB. Air to water gives about 29.5 dB and water to steel about 9.2 dB with the preset values.
What is the difference between acoustic impedance and specific acoustic impedance?+
Specific acoustic impedance is pressure divided by particle velocity at a point, in rayl. Acoustic impedance proper is pressure divided by volume flow rate, in Pa s/m3. For a plane travelling wave the specific impedance equals the characteristic impedance rho c.
Does the pressure reflection coefficient change sign?+
Yes. If the second medium has the lower impedance, r is negative and the reflected pressure wave is inverted. If the second medium has the higher impedance, r is positive and the reflected wave keeps its sign. The intensity reflection R is always between 0 and 1.
How is acoustic impedance different from seismic impedance?+
The formula Z = rho v is the same, but seismic work uses rock densities and P-wave or S-wave velocities at layer boundaries and often at varying incidence angles. This page treats ordinary acoustic waves in fluids and solids at normal incidence.
What impedance should a matching layer have?+
For a single quarter-wavelength layer between two media the ideal impedance is the geometric mean sqrt(Z1 Z2). The calculator shows this value, for example about 3.56 MRayl between soft tissue and bone, and 8.28 MRayl between water and steel.
Can the transmitted pressure be larger than the incident pressure?+
Yes. When the second medium has the higher impedance the pressure transmission coefficient 2 Z2/(Z1 + Z2) approaches 2. The intensity still cannot exceed the incident intensity, because the particle velocity in the second medium is correspondingly smaller.
Does the angle of the sound wave matter?+
Yes. This calculator assumes normal incidence, a wave hitting the boundary at a right angle. At oblique angles the sound speeds also set the refraction angle, and the reflection formulas use Z divided by the cosine of the angle in each medium.

What is acoustic impedance and how do you calculate it?

For a plane wave the characteristic acoustic impedance is Z = rho c, the density times the speed of sound. Its SI unit is the pascal second per metre, called the rayl. Air at 20 C gives about 413 rayl.

What is the acoustic impedance of air?

About 413 rayl (Pa s/m) at 20 C, from a density of 1.204 kg/m3 and a sound speed of 343.2 m/s. It changes slightly with temperature and pressure.

What is the acoustic impedance of water?

About 1.48 million rayl (1.48 MRayl) for fresh water at 20 C, from 998.2 kg/m3 and 1482 m/s. Seawater is a little higher, near 1.54 MRayl.

How do you calculate the sound reflection coefficient?

At normal incidence the pressure reflection coefficient is r = (Z2 - Z1)/(Z2 + Z1) and the intensity reflection is R = r squared. The transmitted intensity share is T = 1 - R = 4 Z1 Z2/(Z1 + Z2) squared.

Why does sound not pass from air into water?

The impedances differ by a factor of about 3580, so 99.89 percent of the incident intensity is reflected and only about 0.11 percent is transmitted, a loss of about 29.5 dB.

What is impedance mismatch loss in dB?

It is minus 10 log10 of the intensity transmission T. A perfect match (Z1 = Z2) gives 0 dB. Air to water gives about 29.5 dB and water to steel about 9.2 dB.

What is the difference between acoustic impedance and specific acoustic impedance?

Specific acoustic impedance is pressure divided by particle velocity at a point, in rayl. Acoustic impedance proper is pressure divided by volume flow rate, in Pa s/m3. For a plane travelling wave the specific impedance equals the characteristic impedance rho c.

Does the pressure reflection coefficient change sign?

Yes. If the second medium has the lower impedance, r is negative and the reflected pressure wave is inverted. If the second medium has the higher impedance, r is positive and the reflected wave keeps its sign.

How is acoustic impedance different from seismic impedance?

The formula Z = rho v is the same, but seismic work uses rock densities and P-wave or S-wave velocities at layer boundaries and often at varying incidence angles. This page treats ordinary acoustic waves in fluids and solids at normal incidence.

What impedance should a matching layer have?

For a single quarter-wavelength layer between two media the ideal impedance is the geometric mean sqrt(Z1 Z2). The calculator shows this value, for example about 3.56 MRayl between soft tissue and bone.

Is the transmitted pressure ever larger than the incident pressure?

Yes. When the second medium has the higher impedance the pressure transmission coefficient 2 Z2/(Z1 + Z2) approaches 2. The intensity still cannot exceed the incident intensity, because the particle velocity is smaller.